Bedienungsanleitung Metabo BAS 600 (Seite 11 von 38) (Deutsch, Englisch, Holländisch, Französisch)

451402

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

2 Band Saw Installation

Remove wrapping and check for any visible damage

which may have occurred during transport. If damage is

detected notify your dealer immediately.

For a firm stand and vertical stability this maschine has

to be bolted to the floor. For this purpose four 13 mm

holes are provided in the machine's base. Drill holes in

floor according to the drilling pattern shown in fig. 3.

533

593

601

370

300

430

Fig. 3

Fig. 2

Fig.1

1.3 Safety Information

1. Before switching on be sure that all guards are in place

and securely locked.

2. Always disconnect from power when changing blades

and servicing machine.

3. Do not use cracked or bent saw blades.

4. Replace table insert if slot has enlarged.

5. When cutting with the table tilted always set fence to

the right of the blade to support the workpiece.

6. When cutting round stock use a suitable jig to prevent

the work from turning (fig. 1).

7. When cutting boards in an upright position use a

suitable push block to prevent kickback (fig. 2).

8. Before tilting the table for bevel cuts replace the table

insert (209) with the wide slot table insert (208).

9. For safe operation and to keep dust emission within

the legal limits a dust collector with a minimum air flow

rate of 20 m/s must be connected to this band saw.

To facilitate better handling and prevent damage to

projecting parts during transport, this machine is shipped

partly disassembled. After unpacking the saw table, rip

fence and crank handle have to be installed before the

saw can be operated.

● Remove rip fence carrier extrusion from saw table to

have access to the slot in the table.

● Place saw table on the upper table trunnion.

● Bolt table to trunnion with 4 each serrated lock washers

Ø 8.4 mm and hexagon head screws M 8x16.

Fig. 4

Residual risks of woodworking machines

Even if

● all safety guards are used

● the machine is used according to its specified condition

of use

● all relevant safety regulations are observed

the following residual risks remain:

- hearing damage by noise emission

- risk of injury by hand contact with the uncovered

cutting area of the blade

- risk of injury when changing a blade (cuts)

- risk of injury by ejection of workpieces or parts thereof

- squashing of fingers

- risk of being drawn into the cutting tool when using a

power feed attachment

- danger of kickback

- inhalation of harmful dusts generated when working

wood, especially oak and beech dust.

The principle risks associated with a woodworking

machine are:

- workpiece kickback

- tilting of the workpiece due to insufficient support

- contact with the cutting tool

- being drawn into revolving tools

- ejection of objects such as knots or other workpiece

parts

The principle danger zones of a woodworking machine

are:

- the work area

- the close proximity to revolving machine parts

- the kickback area

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo BAS 600 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info