511053
10
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
10
ENGLISH
ENG
Pull the plug out of the plug socket before any
adjustments, conversions or servicing are
performed.
The rated speed of the sanding belt must be at
least equal to the belt speed in idling marked on
the power tool. A sanding belt running faster than
its rated speed can break and fly apart.
Check prior to each use that the sanding belt is
correctly attached and is completely on the rollers.
Carry out a trial run: Allow the machine to run at
idling speed for 30 seconds in a safe location. Stop
immediately if significant vibrations occur or if
other defects are noted. If such a situation occurs,
check the machine to determine the cause.
See page 2.
1 Sanding attachment
2 Rotary knob for securing the sanding
attachment and adjusting the belt run
3Cover
4 Arrow (direction of rotation of
drive shaft
)
5 Screw for securing the
cover
6 Sanding belt
7 Tensioner arm for replacing the sanding belt
8 Sanding head
9
Locking screw for
adjusting sanding head
10 Additional handle
11 Sliding switch
12
Adjusting wheel for
setting belt speed
The machine is also available with different acces-
sory parts. An overview can be found on page 4.
Subject to change.
A Sanding belt arm
B Sanding belt, zirconia alumina
C Nylon web band
D Microfibre cloth
E Stainless steel cleaning spray
Before plugging in, check that the rated
mains voltage and mains frequency, as
stated on the rating label, match with your power
supply.
Attaching the additional handle
Always work with the additional handle
attached (10)! Attach the additional handle
on the left or right of the machine and secure.
Attach the additional handle to the side facing
away from the sanding belt (6).
Turning the sanding head (8) to operating posi-
tion
Loosen the locking screw (9) using the hexagon
spanner and, if necessary and depending on the
task at hand, turn the sanding head (8). The
sanding head must be positioned in the permitted
working area as shown (see illustration A, page 2).
Firmly tighten the locking screw (9).
Each time before you start work, verify that
the locking screw (9) is sufficiently tightened
to ensure that the sanding head (8) does not move.
Otherwise, the sanding belt (6) may come in
contact with the user. Loss of control can cause
personal injury.
8.1 On/Off switch, continuous activation
Always guide the machine with both hands.
Switch the machine on first before mounting
it on the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When
switching the machine on and off, keep it away
from dust deposits.
After switching off the machine, only place it
down when the motor has come to a stand-
still.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Switching on/
Continuous activation
:
Push slide
switch (11) forward. For continuous activa-
tion, now tilt downwards until it engages.
Switching off:
Press the rear end of the slide
switch (11) and release.
5Overview
6 Scope of delivery
7 Initial Operation
8Use
0
I
11
17026977_0212 BFE 9-90.book Seite 10 Dienstag, 21. Februar 2012 11:51 11
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo BFE 9-90 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info