511053
11
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
ENGLISH
11
ENG
8.2 Setting belt speed
The belt speed can be preset via the setting wheel
(12) and is infinitely variable.
Positions 1-6 correspond approximately to the
following belt speeds:
1......... 3.8 m/s 4 ........7.8 m/s
2......... 5.4 m/s 5 ........8.4 m/s
3......... 6.9 m/s 6 ........9.0 m/s
8.3 Sanding belt replacement
See illustration B, page 2.
- Manually loosen screw (5) and remove cover (3).
- Pull tensioner arm (7) backwards and remove
sanding belt (6).
- Place the new sanding belt on the rollers such
that its direction of circulation (arrows on the
inside of the sanding belt) matches the arrows (4)
on the cover. Place the sanding belt first on the
drive shaft and then on the roller on the sanding
attachment (1).
- Replace the cover (3) and tighten the screw (5) by
hand.
- Check the belt run and adjust if necessary (see
Section 8.4).
8.4 Adjusting belt run
Using the screw (2), adjust the sanding belt -
while the machine is not in operation and is
plugged out - so that it runs in the centre of the
sanding belt roller.
8.5 Sanding procedure
Switch the machine on first before mounting it on
the workpiece.
Place the machine on the material such that the
sanding belt is parallel to the surface of the work-
piece.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
8.6 Replacing the sanding attachment
See illustration C, page 2.
- Removing the sanding belt (see Section 8.3).
- Remove screw (2), and remove sanding attach-
ment (1).
- Attach the other sanding attachment as shown
(ensure that the nose at the end of the sanding
attachment is pointing in the direction of the
tensioning arm, see illustration C).
- Secure with screw (2).
- Attaching the sanding belt (see Section 8.3).
- Adjusting the belt run (see Section 8.4).
Motor cleaning:
blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model of your
power tool in order to select the correct accessory.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
2
9 Cleaning, Maintenance
10 Tips and Tricks
11 Accessories
12 Repairs
13 Environmental Protection
17026977_0212 BFE 9-90.book Seite 11 Dienstag, 21. Februar 2012 11:51 11
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo BFE 9-90 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info