ENGLISH en
15
7.9 Setting the speed
Select the speed at the setting wheel (26) . See
table for recommended setting wheel positions.
Wood: 3 - 6
Aluminium: . .
Plastic:
8.1 Connect the chip and dust
extraction unit
Danger!
Dust of certain timber species (e.g.
ash) can cause canc
– Use only a suitable dust ext
working.
– In addition, use a dust mask, as not all saw
is collected or extracted.
If you connect the device to a chip and dust
extraction unit:
Connect the chip
mobile all-purpose vacuum cl
extraction adapter nozzle (2 . If needed,
connect the angled extraction adapter (3) .
Ensure that the dust extraction unit meets the
requirements stated in chapter 16. "Technical
Specifications".
Observe the dust colle
instructions as well!
8.2 Installing thrkpiece clamping
device
The workpiece clamping device (11) can be
installe
–F
workpieces:
Insert the workpiece clamping device into the
rear drilling (35) of the table.
– For narrow
workpieces:
Insert the workpiece clamping device into the
front drilling (36) of the table.
8.3 Power-supply connection
Danger! High voltage
Operate machine only on a power source meeting
the following requirements (see also chapter 16.
"Technical Specificatio
– Mains voltage and system frequency must
conform to the voltage and frequency shown on
the machine´s rating label;
– fuse protection by a residual current operated
device (RCD) of 30 mA sensitivity;
– outlets pr
and tested.
Position power supply cabl
interfere with the work and is not damaged.
Use only rubber-jacke
sufficient lead c
2
).
Use extension cables for outdoor areas. When
working outdoors, on
marked extension cable approved for this
purpose.
Avoid accidental start-up. Ensure that the on/off
switch is switched off when ins
the socket.
Before starting work, check to see that the
following are in proper wo
Assume prope
– at the front of the saw;
– in front of the saw;
– next to the line of cut.
Danger!
If possible, fix the worpiece using the workpiece
clamping devi (11) .
Danger of crushing!
When inclining or swiv
reach into the hinge area or below the
Hold the saw
Use during work:
– workpiece
otherwise workpiece would fall off the table
after cutting;
– Chip and dust extraction unit.
Cut only es of dim
safe and secure holding while cutting.
Always hold the workpiece down on the table
and do not jam it. Do not attempt to stop the saw
blade by pushing the workpiece agai
Risk of pers
blocked.
9.1 Straight c
Starting position:
–T (16) pulled out.
–S
– Cutting depth limitation (48) deactivated.
– Turntable is in 0° position, lockin (22)
for turntable is tightened.
– The incl
0° , locking lever (14) for inclined position is
tightened.
– Pulling device at the very rear.
–S (18) of the pulling device has been
loosened.
– Set workpiece stop (30:
Release lockin31). Slide the
workpiece stop (30) (upper and lower part)
such that it supports the workpiec
possible without touching the blade or
protective cover. Fasten with lo
(31).
Cutting the workpiece:
1. Push the workpiece against the parallel guide/
ripping fence and clamp using the workpiece
clamping device (11) .
2. For wider workpieces:
forwards (towards the operator
device).
3. Activate the safety lock (29) ,press on/off
switch (27) and keep pressed.
4. Slowly lower the saw head at the ha
way down and, if requir
rear (away from the operator). During the
sawing process press on
enough for the motor speed not to lower too
much.
5. Cut the workpiece in one
6. Release the on/off switch (27) and slowly let
the saw head swivel back into the upper
starting position.
9.2 Mitre cuts
Starting position:
–T (16) pulled out.
–S
– Cutting depth limitation (48) deactivated.
– The incl
0°, locking lever (14) for inclined position is
tightened.
– Pulling device at the very rear.
–S (18) of the pulling device has been
loosened.
– Set workpiece stop (30:
Release lockin31). Slide the
workpiece stop (30) (upper and lower part)
such that it supports the workpiec
possible without touching the blade or
protective cover. Fasten with lo
(31).
WARNING - Only for KGSV 72 Xact SYM: Align
parallel guides/rippin (30) flush (in one
line). (It is re
catches (33) downwards to that both halves of
the table (9) / parallel guides/ripping fences (30)
lock in the 0° an
– Push both locking levers (32) all the way
downwards.
Cutting the wo
1. Loosen locking lever (22) of
loosen safety catch (21) .
2. Set the desired angle.
Note:
If the safety catch (21) is pushed upwards
turntable locks in the 0°, 15°, 22.5°, 31.6°, 45°
and 60° angle levels. If the safety catch (21) is
pushed downwards all the way, the locking
function is deactivated.
3. Tighten the locking button (22) of the
turntable.
Caution!
In order for the mitre angle not to change during
cutting, the lockin (22) of the turntable
has to be tightened (also in the stop positions!).
4. Cut workpiece, as described for "Straight
cuts".
9.3 Inclined cu
Starting position:
–T (16) pulled out.
– Saw head swivelled upwards.
– Cutting depth limitatio (48) deactivated.
– Turntable is in 0° position, locking button (22)
for turntable is tightened.
– Pull
–S (18) of the pulling device has been
loosened.
– Set workpiece stop (30) :
Release locking31). Slide the movable
workpiece stop (3 (upper and low
such that it supports the workpiece as
possibng the blade or
protective cover. Faste
(31).
For certain angl
to remove the right-hand, m
the workpiece stop (30) entirely, after loosening
the lock screw (31) . Retighten locking screw
(31). (After the saw cut, reattach
and fasten with locking screw (31) so th
not lost.)
Cutting the wo
1. Loosen the locking lever (14) for the
inclinatng of the saw.
2. Slowly tilt the swivel arm into the desired
position.
Pull the latch leve (12) in direction of th
operator side = infinite adjustment of the
swivel arm.
Push the latch lever (12) in direction of the
rear side = lock swive
Note:
The swivel arm l
22.5° and 33.9°.
3. Tighten the locking lever (14) for the
inclinat
Caution!
In order for the mitre angle not to change during
cutting, the locking lever of the
be tightened (also in the stop positions!).
4. Cut the workpiece, as described for "Straight
cuts".
9.4 Double mitre cuts
Note:
The double mitre cut is a combin
and inclined cut. This means,
at an angle to the rear contact edge and at an
angle to the top.
Starting position:
–T (16) pulled out.
– Saw head swivelled upwards.
– Cutting depth limitatio (48) deactivated.
8. Commissioning
9. Operation
