Bedienungsanleitung Metabo KGT 501 (Seite 20 von 60) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

110270

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Disengage locking

pin for crosscut

saw mode.

Let locking pin

engage for table

saw mode.

Information on the nameplate:

− Sturdy and high-precision die-cast

aluminum design for highest tor-

sional resistance and accuracy at

low weight.

− Operating mode conversion from

crosscut saw to table saw without

tools in seconds, by simply turning

the saw table over.

− Foldable workstand – ideal for site

use.

− In crosscut saw mode, the saw head

tilts steplessly through 45°.

− The rotating table turns steplessly

through 45° left and right.

− Will cut compound mitres up to 45°.

− Large-dimensioned saw table pro-

vides a clean, flush support area.

− Robust drive, insensitive to dust.

− Low wear poly-V-belt for optimal

power transmission and long service

life.

5.1 Machine setup

Caution!

Do not carry the machine at the

table; the table is not designed to

bear the weight of the machine.

1. With two persons, hold the machine

at the front (27) and rear (30)

recessed grips and lift it out of the

packaging.

2. Lay machine on its rear side.

3. Loosen the locking clips (28) and

swing legs out until they engage at

the side panel.

4. Hold machine at the rear recessed

grips (30) and lift it up into vertical

position.

5. If necessary, compensate for an

uneven floor with the adjusting foot

(29).

Note:

See the description of the respec-

tive operating mode for details about the

initial operation in crosscut saw or table

saw mode.

5.2 Machine transportation

1. Swing saw table over in position

table saw mode (see "Table saw

mode").

2. Remove blade guard (31).

3. Lower saw blade (32) fully.

4. Remove rip fence (33), if necessary.

5. Hold saw at the rear recessed grips

(34) and lay it on its rear.

6. Run power cable between the two

left legs (38).

7. Unlock the legs on the left (38) and

fold up.

8. Unlock the right legs (36), fold over

the left legs and secure with the

locking clips (37).

9. Hold saw at the tubes (35) below the

saw table when transporting.

If possible use the original carton for

shipping.

5.3 Mains connection

Danger! High voltage

• Operate machine in dry environ-

ment only.

• Operate machine only on a power

source matching the following

requirements (see also "Techni-

cal specifications"):

− outlets properly installed,

earthed and tested;

− mains voltage and system fre-

quency conform to the voltage

and frequency shown on the

machine's nameplate;

− fuse protection by a residual

current operated device (RCD)

of 30 mA sensitivity;

− system impedance Z

max.

at the

interconnection point (house

service connection) 0.35 Ohm

maximum.

Note:

Check with your local Electric-

ity Board or electrician if in doubt

whether your house service connec-

tion meets these requirements.

• Position power supply cable so it

does not interfere with the work

and is not damaged.

20 Manufacturer

21 Serial number

22 Machine designation

23 Motor specifications (see also

"Technical specifications")

24 Year of make

25 CE-mark – This machine con-

forms to the EC directives as per

Declaration of Conformity

26 Dimensions of permissible saw

blades and riving knives

4. Special product features

24 25 26

5. Installation and transport

31 32 33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KGT 501 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info