Bedienungsanleitung Metabo KGT 501 (Seite 22 von 60) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

110270

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

7.3 Operation

Danger!

• Before starting any work, check

to see that the following are in

proper working order:

− saw blade;

− retractable blade guard;

− fence.

• Assume proper operating posi-

tion:

− at the front of the saw;

− in front of the saw;

− to the side of the line of cut.

• If the type of work requires, use

the following:

− work support – for long stock,

which would otherwise fall off

the table on completion of the

cut;

− dust collector;

− work clamp.

• Always hold the workpiece down

on the table and against the

fence.

• If small cutoffs will result when

cutting, use the auxiliary fences.

• Make sure the angle of inclination

will not change when sawing

(Tighten the stopping lever for the

sawhead tilt).

Standard cross cuts

Starting position:

− sawhead fully raised;

− rotating table in 0° position, locking

pin (51) is engaged and the rotating

table's stopping lever (50) is tight-

ened;

− The sawhead bevel tilt is 0°, the

ratchet lock lever for the sawhead tilt

is fully tightened.

Execution:

1. Hold workpiece against the fence.

2. Start machine (press green switch

button).

3. Pull the release lever – the retracta-

ble blade guard opens.

4. Holding it at the saw handle, lower

the sawhead onto the workpiece.

When sawing exert only moderate

pressure, to prevent the motor

speed to drop too much.

5. Cut workpiece in a single pass.

6. Raise sawhead to its upper starting

position.

7. If no further cutting is to be done

immediately afterwards, switch the

machine OFF (press red switch but-

ton).

Mitre cuts

Note:

A mitre cut cuts the workpiece at

an angle between -45° and +45° against

the rear guide edge.

Starting position:

− sawhead fully raised;

− saw blade is vertical to the saw

table.

Execution:

1. Loosen the rotating table's stopping

lever (50).

2. Pull out the locking pin (51) and turn

counter-clockwise.

3. Set to desired angle.

4. Tighten stopping lever (50), if nec-

essary let locking pin (51) engage.

Note:

The locking pin of the rotating

table engages at +45°, 0° and -45°.

Caution!

In order to prevent the mitre

angle from changing during cutting,

the stopping lever must always be

tightened.

5. Cut workpiece as detailed under

"Standard cross cuts".

Bevel cuts

Note:

A bevel cut cuts the workpiece at

an angle between 0° and 45° from verti-

cal.

Starting position:

− sawhead fully raised;

− rotating table locked in the 0° -posi-

tion.

Execution:

1. Loosen the ratchet lock lever (52)

for sawhead tilt at the rear of the

saw.

2. Tilt sawhead to desired angle

against the workpiece's surface.

3. Tighten the ratchet lock lever (52).

4. Cut workpiece as detailed under

"Standard cross cuts".

Compound mitre cuts

Note:

The compound mitre cut is a

combination of mitre and bevel cuts.

This means the workpiece is cut at an

angle other than 90° against the rear

guide edge and against its surface.

Starting position:

− sawhead fully raised;

− rotating table locked in desired posi-

tion.

− sawhead tilted to desired angle

against the workpiece's surface and

locked.

Execution:

The actual cutting operation is per-

formed as detailed under "Standard

cross cuts".

45°-0°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KGT 501 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info