595069
13
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
ENGLISH en
13
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical treatment
immediately.
LED working light
(8)
: Do not observe the LED
radiation directly with optical instruments.
See page 2.
1 Scale (diagonal cut angle)
2 Locking screw (diagonal cuts)
3 Spindle locking button
4Locking button
5Trigger switch
6 Connector (extraction connection piece / dust
ejection)
7Guide plate
8LED lights
9 Parallel stop
10 Cutting indicator
11 Locking screw (parallel guide)
12 Battery pack
13 Battery pack release
14 Depot for hexagon wrench
15 Hexagon spanner
16 Adjusting screw (adjust saw blade angle)
17 Lock nut (adjust saw blade angle)
18 Scale (depth of cut)
19 Locking screw (depth of cut)
20 Saw blade fixing screw
21 Outer saw blade flange
22 Saw blade
23 Movable safety guard
24 Inner saw blade flange
25 Lever (swivelling back the movable guard)
26 Capacity and signal indicator
27 Capacity indicator button
Integral LED working light for illuminating the
cutting line
Safety brake for stopping saw blade quickly when
switching off the machine.
Electronic overload protector with integral
temperature monitor protects the machine and
the battery pack.
Electronic single-cell monitor that extends the
service life of the battery pack.
I
Remove the battery pack from the machine
before any adjustment or maintenance is
carried out. Before fitting the battery pack, make
sure that the machine is switched off.
7.1 Battery pack
Charge the battery pack before use
(12)
.
If performance diminishes, recharge the battery
pack.
"Li-Power" li-ion battery packs have a capacity
and signal indicator: (26)
- Press the (27) button, the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removal:
Press the battery pack release
(13)
button and pull the
battery pack
(12)
upwards.
Inserting:
Slide in the battery pack
(12)
until it engages.
7.2 Setting depth of cut
Loosen the locking screw (19). Read the depth of
cut that has been set from the scale (18). Tighten
the locking screw again.
It is advisable to set the depth of cut in such a way
that no more than half of each tooth on the saw
blade juts out under the workpiece. See illustration
on page 3.
7.3 Slanting saw blade for diagonal cuts
Loosen the locking screw (2). Tilt the motor part
against the guide plate (7). Read the angle which
has been set from the scale (1). Tighten the locking
screw again.
7.4 Correcting the saw blade angle
If, at 0°, the saw blade is not at right angles to the
guide plate: release lock nut (17) and correct saw
blade angle with adjusting screw (16). Then
retighten the lock nut.
7.5 Extraction connection piece / dust
ejection
Sawdust extraction:
connect a suitable dust extraction unit with suction hose
to the connection piece to extract the sawdust. (6)
Sawdust ejection:
Turn the nozzle (6) to the desired position (away from
body if possible).
8.1
The machine's multifunctional monitoring
system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode. A warning signal sounds (continuous
beeping). The beeping stops after a maximum of 30
seconds or when the trigger is released (5).
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost flat (the electronics
5. Overview
6. Special Product Features
7. Initial Operation, Setting
8. Use
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo KSA 18 LTX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info