Bedienungsanleitung Metabo KSE 55 Vario Plus PartnerEdition (Seite 12 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595377

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISHen

12 Lock nut (adjust saw blade angle)

13 Adjusting screw (adjust saw blade angle)

14 Cable guide

15 Rotational speed preselection wheel

16 Signal display

17 Lever (for swivelling back the movable guard)

18 Depot for hexagon wrench

19 Hexagon spanner

20 Locking screw (

for setting cutting depth

)

21 Clamping lever (for setting cutting depth)

22 Cutting depth stop (for setting cutting depth) and

cutting depth indicator

23 Scale (depth of cut)

24 Spindle locking button

25 Inner saw blade flange

26 Saw blade

27 Saw blade fixing screw

Before plugging in, check to see that the rated

mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Pull the plug out of the plug socket before any

adjustments or servicing are performed.

6.1 Setting cutting depth

Note: It is advisable to set the depth of cut in such a

way that no more than half of each tooth on the saw

blade juts out under the workpiece. See illustration

on page 2.

- Release locking screw (20). Lift motor section

against guide plate (depth of cut = 0 mm).

- Preselect the desired depth of cut with the cutting

depth stop (22), see illustration, page 2. To do

this, release the clamping lever (21), set the

cutting depth stop (22) on the scale (23) to the

desired depth of cut and clamp the clamping lever

again.

- Press the motor section downwards as far as the

stop.

- Tighten locking screw (20) again.

Note: the clamping power of the locking screw (20)

can be adjusted. Unscrew the screw on the lever to

do this. Remove lever and mount offset

counterclockwise. Secure with screw. When doing

this, note that the cutting depth setting device

moves freely when the lever is open.

6.2 Slanting saw blade for diagonal cuts

Loosen the two locking screws (5) to make the

setting. Tilt the motor section against the guide

plate. Read the angle which has been set from the

scale (11). Retighten the front and then the rear

locking screw (5).

6.3 Correcting the saw blade angle

The

saw blade angle is set ex works.

If, at 0°, the saw blade is not at right angles to the

guide plate: release locking screws (5). Release

lock nut (12) and correct saw blade angle with

adjusting screw (13). Then retighten the lock nut.

Retighten both locking screws (5).

6.4 Rotational speed preselection

Select the speed at the setting wheel (15). For

recommended speeds, see page 3.

6.5 Setting extraction nozzle / chip ejection

Sawdust extraction:

remove nozzle (9) if necessary. To extract the

sawdust, connect a suitable extraction unit with

suction hose to the machine.

Sawdust ejection:

Fit nozzle (9) and turn in desired direction (away

from body if possible).

7.1 Switching on and off

Switching on: Press locking button (7) and hold in;

then actuate the trigger (8).

Switching off: Release the trigger (8).

7.2 Signal display

The signal display (16) lights up briefly when the

machine is switched on and indicates operational

readiness. If the signal display lights up during

operation, this indicates overloading. Reduce the

load on the machine.

7.3 Working instructions

Lay out the mains cable such that the cut can be

executed without obstruction.

For this purpose, the mains cable can be held by the

cable guide (14).

The marking (1) on the upper guard assists you in

positioning the saw on the workpiece and when

sawing. In the case of maximum cutting depth, it

marks approximately the outside diameter of the

saw blade and thus the cutting area.

Do not switch the machine on or off while the

saw blade is touching the workpiece.

Let the saw blade reach its full speed before

making a cut.

When the hand-held circular saw is added, the

movable guard is swung backwards by the

workpiece.

Open the bottom guard by hand only when making

special cuts, such as plunge cuts and angle cuts.

Open the bottom guard with the lever (17) and

release it as soon as the saw blade has penetrated

the workpiece. For all other sawing, the lower guard

must be released.

When sawing, never remove the machine

from the material with the saw blade turning.

Allow the saw blade to come to a standstill.

If the saw blade blocks, turn the machine off

immediately.

Sawing along a straight line:

the edge (2) serves as the cutting indicator. The

6. Initial Operation, Setting

7. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KSE 55 Vario Plus PartnerEdition Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info