Bedienungsanleitung Metabo LF 724 S (Seite 10 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599620

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISHen

in a well ventilated area, and work with approved

safety equipment, such as dust masks that are

specially designed to filter out microscopic

particles.

Observe the relevant guidelines for your material,

staff, application and place of application (e.g.

occupational health and safety regulations,

disposal).

Collect the generated particles at the source, avoid

deposits in the surrounding area.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- Use an extraction unit and/or air purifiers

- Ensure good ventilation of the workplace and

keep clean using a vacuum cleaner Sweeping or

blowing stirs up dust

- Vacuum or wash the protective clothing Do not

blow, beat or brush

See page 2.

1 Protective flap

2 Locking button

3 Additional handle

4 Sliding switch ( 0 / I )

5Handle

6 Extraction nozzle

7 Extraction connection piece (Ø 35 mm)

8Graver

9 Multi-socket spanner

a Hexagon

b Torx

10 Planing base

11 Reversible blade

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle (3)

attached! Attach the auxiliary handle as

shown.

Always work with an extraction

system to guarantee perfect

machine operation.

Always guide the machine with both hands on

the handles (3), (5) provided.

7.1 Switching On and Off the paint remover

Switching on

Lift paint remover so that the cutter head is free.

Push the slide switch (4) forward.

I On

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Switching off

Lift paint remover so that the cutter head is free.

Press the rear of the slide switch (4). The slide

switch jumps back.

0 Off

Wait until the cutter head is at a standstill

before setting down the machine. An exposed

cutter head can get caught on the surface and lead

to a loss of control and possible serious injury.

7.2 Locking the cutter head

Danger of injury from the sharp edges of the

reversible blades. Lock the cutter head only

when the cutter head is idle! Switch off paint

remover and pull the mains plug from the socket!

Lay the paint remover on its side.

Press the locking button (2) up to the stop and keep

pressed.

Simultaneously turn the cutter head using the

hexagonal wrench (9-a) (any direction). Turn until

the pressed locking button noticeably engages and

the cutter head is locked.

7.3 Setting the axial cutting depth

Danger of injury from the sharp edges of the

reversible blades. Set the axial cutting depth

only when the cutter head is idle! Switch off paint

remover and pull the mains plug from the socket!

Lock the cutter head and keep the locking button

pressed.

5. Overview

6. Commissioning

7. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo LF 724 S Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info