Bedienungsanleitung Metabo LF 724 S (Seite 11 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599620

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH en

Set the desired cutting depth by turning the setting

screw using a hexagonal wrench (9-a).

Possible cutting depths: 0-0.3 mm

Start with a small cutting depth and increase it

gradually until you have reached the optimum

setting for the workpiece to be processed.

Do not leave the hexagonal wrench in

place!

7.4 Attaching / Removing the extraction

connection piece

Use a Metabo all-purpose vacuum cleaner for dust

extraction purposes.

Attachment

Push the extraction connection piece (7) until it

engages into the extraction nozzle (6).

Now the desired extraction unit can be connected to

the extraction connection piece with the pipe

diameter 35 mm.

Removal

Press the lip and simultaneously remove the

extraction connection piece (7) from the extraction

nozzle (6).

8.1 Guiding the paint remover

Always use two hands to guide the paint remover

backwards where possible over the surface of the

workpiece being processed. When holding the

paint remover down, ensure that the low pressure

exerted is distributed evenly over the area of the

planing base.

8.2 Presenting the tool to the edge of a

workpiece

See diagram A: Hold the paint remover parallel with

the surface of the workpiece. When presenting the

tool, ensure that the planing base is in contact with

the largest possible area of the surface (10).

8.3 Operation

See diagram B: Guide the paint remover in such a

way that the planing base (10) is always positioned

on the surface that has not yet been processed. If

you proceed as shown, a narrow section is left over.

See figure C: You can remove this section by setting

the cutting depth to 0 mm (see section 7.3) and now

always guide the planing base (10) over the

processed surface.

8.4 Smoothing

Reduce the cutting depth to achieve a smooth

surface finish.

Danger of injury from the sharp edges of the

reversible blades. Effect maintenance work

only when the cutter head is idle! Switch off paint

remover and pull the mains plug from the socket!

Always wear personal protective equipment,

safety goggles, ear protectors, protective

gloves and heavy-duty footwear during work and for

all setting, conversion and maintenance tasks!

9.1 Cleaning the reversible blades

Paint might build up under the cutting edges of the

reversible blades. In this case, clean the edges of

the reversible blades using the graver (8).

9.2 Turn/replace the reversible blades

Use original Metabo reversible blades only.

Order no.: 6.31720 (4 pieces)

Order no.: 6.31660 (10 pieces)

Blunt edges of the reversible blades increase

the danger that the paint remover jams during

the milling operation and kicks back. Therefore turn/

replace blunt reversible blades in good time!

If required, clean Torx of the reversible blades using

a graver (8).

Axial reversible cutting plates:

Locking the cutter head.

8. Tips and Tricks

9. Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo LF 724 S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info