Bedienungsanleitung Metabo MAG 28 LTX 32 (Seite 16 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595085

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

ENG

General notes:

- Centre the position at which the hole is to be

drilled.

- Note: If the display (24) is switching from red to

green (see diagram, page 3), a small amount of

holding power is available, which can be used

when fastening and aligning the magnetic drill

stand.

- Align the magnetic drill stand so that the drill bit

is above the centre marking.

- Fully activate the magnet in the magnetic drill

stand.

- Pull out the lock switch (6).

- Finally, switch on the driving unit (move the

switch (8) to the "I" position).

- If necessary, switch on the cooling lubrication

unit (see chapter 7.2.

- Start the drilling operation with minimum feeding

force. When the drill bit has started to drill,

slightly higher feeding force can be applied.

Excessive feeding force leads to premature wear

of the drill bit. Ensure that the chip flow is regular

- Use a wire hook

to remove the chips.

- If the drilled metal piece is not automatically

ejected by the core drill bit: remove it using a

tool.

Special notes on tools with morse taper shank

MK2:

Inserting

tool

To prevent the driving unit from

moving up/

down accidentally

: depress the lock switch

(6).

The tool is only guaranteed to fit perfectly in

the drill spindle (13) if the female taper of the

drill spindle and the taper shank of the tool are free

of dirt and grease.

Caution! Never use excessive force to press

tools into the female taper of the drill spindle!

Always use sharp tools in perfect condition.

Switch off the machine. Remove battery

pack from machine.

Tools with a taper shank MK2 can be used directly

in the female taper of the drill spindle (13).

Driving out

the tool:

Insert the removal tool (12) - with the sloping edge

against the tool - in the slot (11) on the machine

neck. If the removal tool cannot be inserted

through the drill spindle, you should turn the drill

spindle (13) slightly by hand. Drive out the tool by

knocking lightly on the removal tool with a hammer

(12).

Special notes on tools with Weldon shank

19 mm:

To prevent the driving unit from

moving up/

down accidentally

: depress the lock switch

(6).

First, insert the industrial holder 6.26602 (see

Chapter 10 Accessories).

When inserting the attachment, ensure that

the side pin of the industrial attachment

engages with the anti-twist device (14).

(17)Then connect the quick-action coupling from

the c

ooling lubrication unit to the connecting

piece on the industrial attachment

6.26602.

Inserting the

tool

- Insert the centring pin for the core drill bit (see

chapter 10 Accessories) in the tool.

- Insert the tool in the tool holder (16) so that both

surfaces (on the cylindrical part of the tool) are

located at the positions of the threaded pins (15).

- Guide the tool upwards as far as it will go

(against the pressure of the integral spring) and

tighten the threaded pins (15) using the Allen key.

Removing

the tool

- Release the two threaded pins (15).

Perform regular maintenance work, cleaning and

lubrication.

Remove the battery pack from the machine before

any adjustments, conversions or servicing are

performed.

To lubricate the rack and pinion that moves the

slide plate (7) up and down, you should occasion-

ally apply some multi-purpose grease to the rack.

Coat the sliding surfaces of the slide plate (7) with

multi-purpose grease.

Occasionally apply a drop of machine oil to the

area where the shaft penetrates (23) the magnet

section.

To prevent rust, occasionally rub the magnet block

with a cloth soaked in oil.

Backlash of the slide plate

The backlash of the side plate is set ex works.

The side plate (7) must be adjusted so that it can

still be moved freely up and down (when the

driving unit is installed), and so that it will remain in

any position without the weight of the driving unit

pulling it down.

If necessary, you can adjust the backlash of the

slide plate (7) using the three threaded pins (5):

release the counternuts, tighten the threaded pins

and fasten the counternuts again.

8 Cleaning, Maintenance

17027057_0211 MAG 28 LTX 32.book Seite 16 Dienstag, 1. März 2011 1:15 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo MAG 28 LTX 32 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info