Bedienungsanleitung Metabo MFE 30 (Seite 15 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600608

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH en

The support flange (16) must always be fitted onto

the spindle with the sheath facing out (as shown in

the pictures (a) – (d). Pay attention to ensure that

the support flange (16) cannot be rotated.

Fit the diamond cut-off wheels and pay

attention to the correct direction of

rotation. The direction of rotation is specified by

arrows on the diamond cut-off wheels and on the

guard (10).

Arrangement of the spacer rings (17) and the

diamond cut-off wheels (according to desired

groove width) as in the pictures (a) – (d).

Lock the spindle by pressing the locking button (13)

and tighten the sheath (11) with the two-hole

wrench.

Then swing the guard (10) and guide shoe (12)

back into place, screw in the hex screw (4) and

tighten the hex screw (8) up again.

Carry out a test run: Position yourself and

bystanders away from the plane of the rotating

wheel and run the power tool at maximum no-load

speed for one minute. Damaged wheels will

normally break apart during this test time. Stop

immediately if significant vibrations occur or if other

defects are noted. If such a situation occurs, check

the machine to determine the cause.

If you remove the front diamond cut-off wheel and

leave only the rear wheel on the machine, the wall

chaser is then suited for cutting through materials

(e.g. tiles).

After undoing the cross handled screw (2) you can

set the desired cutting depth using the scale (1).

Tighten the cross handled screw (2) back up again.

Caution! Never work without a dust extraction

device. Dusts can be harmful to health!

Never work without a dust extraction device.

The motor can quickly choke on stone dust.

Use a suitable Metabo vacuum cleaner.

To extract stone dust generated during work with

the wall chaser, insert the suction hose 30 344 (4 m)

in the aperture of the extraction unit (6). The

bayonet catch prevents the suction hose from

coming loose while the machine is in operation.

Using a second suction hose 6.30344 allows you to

set up the extraction unit at a distance of up to 8 m

from the work place.

(Suction hose not included in scope of delivery).

To connect a suction hose without a bayonet catch,

use the connection adapter provided.

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

Switching on: Push the slide switch (15) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (15) and release it.

8. Using the machine with only

one diamond cut-off wheel

(a)

(b)

(c)

(d)

9. Depth of cut

10. Extracting the stone dust

11. Switching on and off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo MFE 30 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info