Bedienungsanleitung Metabo MFE 30 (Seite 16 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600608

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISHen

Always guide the device with both hands on

the main handle (5) and side handle (3).

Only use the wall chaser with the side handle

(3) attached!

Position the side handle so that it can be

gripped firmly without touching the guard.

Contact with live wires energises the metal parts of

the housing and can cause electric shock to the

operator.

The side handle (3) may be adjusted after the screw

(14) is undone. Bring the side handle to the desired

position and tighten the hex screw (14).

At the rear end of the guide shoe (12) there is a

triangular marking (9). The marking is on the

extension of the rear diamond cut-off wheel and is

used, when cutting grooves, as a cut indicator.

Place the wall chaser (with the motor switched on)

with the guide shoe (12) on the surface into which a

groove is to be cut, and slowly guide down until the

set cutting depth has been reached.

Then pull the machine in the chase direction, e.g.

from top to bottom as shown in Fig. A below (page

4) or – for horizontal chases – back towards itself as

shown in Fig, B (page 4).

Once the groove is complete, switch off the

tool and hold it steady until the diamond cut-off

wheel comes to a stop. Never attempt to remove

the cutting disc from the cut while the wheel is

in motion otherwise kickback may occur. Lay

the tool on its side.

You can remove the remaining strip between the

two chases with the chase extraction chisel

provided.

Grooves of greater depth cannot be cut into

hard material (e.g. cement) in one movement.

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of the

power tool.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

14.1 Safety clutch

There is an automatic safety coupling built-in to the

gears of the wall chaser. This protects the operator

from the high torque that may, for example, occur if

the diamond cut-off wheel is canted during work.

The safety coupling protects and at the same time

takes the strain off the motor and the gears of the

machine. When the safety coupling engages,

immediately switch the motor off (do not allow the

coupling to drag!),

14.2 Electronic overload protection

In the event of a brief, very high overloading of the

machine, the integrated electronic overload

protection limits the power consumption and thus

prevents the overheating of the machine.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

Metabo diamond cut-off wheels:

diameter 125 , laser-welded, suitable for dry cutting,

bore = 22.2 mm, for wall chaser MFE 30

Area of use Order number

for hard and medium-hard

materials (e.g. concrete, including reinforced

concrete) 6.24541

for abrasive materials

(e.g. abrasive cement, sandstone,

sand-lime brick, aerated concrete and similar)

6.24641

For a complete range of accessories, see

www.metabo.com or the catalogue.

Carbon brushes: When the carbon brushes on the

machine are worn, the automatic switch-off system

cuts out the power and the machine comes to a

standstill.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

The sanding dust generated may contain

hazardous materials: do not dispose of with the

household waste, but at a special collection point

for hazardous waste.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Directive 2002/

96/EC on waste electrical and electronic equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

12. Working With the Wall Chaser

13. Cleaning

14. Overload protection

15. Accessories

16. Repairs

17. Environmental Protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo MFE 30 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info