Bedienungsanleitung Metabo Multi 260S (Seite 21 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

3. Remove wooden block and lower

the combination machine so it will

stand on the protection covers.

4. Lift combination machine at the side

(2) opposite the transport handle.

5. Place wooden block under the lifted

side of the combination machine.

6. Put wheels (4) from below on the

two lifted feet, making sure they go

all the way up. Tab fold (5) with a

plastic tip hammer or similar, if nec-

essary.

7. Remove wooden block and lower

combination machine on the wheels.

4.3 Thicknesser bed hand-

wheel installation

1. Place handwheel (6) on shaft (7).

2. Tighten fastening screw (8) with a

4 mm hex key.

4.4 Further preparations

1. Insert the spindle moulder’s table

insert (9) in the table.

2. Put push stick (10) (feeding aid) into

its bracket

4.5 Relocating the machine

1. Extend transport handle fully.

2. Lift combination machine with the

transport handle (1) until the wheels

make contact with the floor.

3. Move combination machine to the

desired location and set it down.

4. Push transport handle fully in.

4.6 Mains connection



Danger! Electrical Hazard.

Operate in dry environment

only.

Operate machine only on a power

source matching the following

requirements (see also "Technical

Specifications"):

− protected by a residual current

operated device (RCD) of 30 mA

capacity;

− outlets properly earthed;

− 5-wire three-phase outlets with

neutral lead;

− when a dust collector is used it

must also be properly earthed.

Position power supply cable so it

does not interfere with the work and

is not damaged.

Protect power supply cable from heat,

aggressive liquids and sharp edges.

Use only extension cables of suffi-

cient lead cross-section.

Do not pull on power supply cable to

unplug.



Check direction of rotation!

Depending on the phase

sequence it is possible that the

motorshaft will turn in reverse rota-

tion. This can cause damage to the

machine. Therefore – after each con-

nection to a different power outlet –

before putting on the flat belts the

direction of rotation must be che-

cked: The arrow on the belt pulley

must point in the direction of rotation.

With an incorrect direction of rotation

the phase sequence needs to be cor-

rected by a qualified electrician at eit-

her the power outlet or the power

cable.

ON/OFF switch



Note:

The ON/OFF switch can be

locked to prevent unauthorized use. For

starting the ON/OFF switch must be

unlocked.

To unlock the ON/OFF switch:

1. Push stopper (11) up.

2. Unlock red OFF button (12) by turn-

ing clockwise.

To switch ON:

• Press black ON button (13).

To switch OFF

• Press red OFF button (12).

To lock the ON/OFF switch:

1. Press the red OFF button (12).

2. Pull the stopper (11) downwards

and out.

Block the stopper with a padlock, if

necessary.

Belt drive

With the belt drive the motor power is

transmitted for the individual operating

modes:

− jointing – thicknessing – mortising;

− sawing and

− moulding.

In addition, the belt drive provides two

different speed settings in operating

modes mortising and moulding.

The belt drive is accessed by opening

the access door.

To change between operating modes

and/or speeds the flat belts are changed

on the pulleys. Detailed information can

be found in the chapters explaining the

relevant operating mode.

5.1 General safety devices

Access door with safety contact

The access door (14) prevents contact

with drive components inside the combi-

nation machine, while it is running. To

provide this protection the access door is

equipped with a safety contact, which

5. Operating Elements

12 1311

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info