Bedienungsanleitung Metabo Multi 260S (Seite 23 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

− Always plane the workpiece over its

entire length.



Risk of injury by touching the

rotating cutterblock:

− Always keep your hands well clear

of the cutterblock.

− When jointing, use the jointer

fence to provide firm support for

the workpiece. Use an auxiliary

fence when planing thin or nar-

row stock, to keep your hands at

a safe distance from the cutter-

block.

− Always cover the part of the cutter-

block that is not covered by the

workpiece with the cutterblock

cover.

− Adjust the cutterblock cover exactly

to the dimension of the workpiece.

− Never reach with your hands under

the cutterblock cover when guiding

the workpiece!

− Use workpiece supports (such as

table extensions) to keep long

stock from losing its balance.

− Plane only stock which rests

securely on the table.

− Use a feeding aid (push block) when

planing a small workpiece, which

can not be guided with a sufficient

safety distance to the cutterblock.

− Do not pull the workpiece back over

the unguarded cutterblock!



Risk of injury by cuts with the

cutterblock at standstill:

− Always cover the cutterblock with

the guard extrusion of the cutter-

block cover when the machine is not

used as thickness planer.

6.3 Operation

1. Place stock against the jointer fence

(29).

2. Adjust cutterblock guard extrusion

(30):

− Planing the face of a plank or work-

pieces up to 75 mm thick:

Use the adjusting screw (31) to

adapt the guard extrusion to the

height of the workpiece. When guid-

ing the workpiece, the hands slide

over the guard extrusion.

− when planing narrow edges (edge

jointing) or workpieces more than

75 mm thick:

Loosen adjusting screw (32) to

adapt the guard extrusion to the

width of the workpiece.

3. Adjust depth of cut with lever (33)



Note:

The max. chip removal in a single

pass is 4 mm.

4. The thicknesser feed can be

switched-off for surface planing. To

switch off, pull lever (34) out until it

engages.

5. Start motor.

6. Assume proper operating position:

position yourself to one side of the

infeed table.

7. Feed workpiece straight across the

infeed table, holding your fingers

close together, guiding the work-

piece with the palm of your hands.

8. Switch machine off if no further plan-

ing is to be done immediately after-

wards.

Workpiece dimensions

• Width: max. 259 mm.

• Thickness: at least 4 mm more than

the set planing thickness.

Tips and tricks

• Plane stock with the grain, if possi-

ble.

• Use roller supports on both sides of

the planer/thicknesser when work-

ing long stock.

• It is better to make several passes

with less chip removal, than making

only a few passes with a high depth

of cut.

• When surface planing a warped

(twisted) board, place on infeed

table with the hollow side facing

down.

• When surface planing short work-

pieces:

− use push stick;

− feed workpiece with the small

face first;

− guide workpiece turned approx.

20° against the direction of feed.

• Keep surfaces of planing beds clean

– in particular, remove resin residue

with a suitable cleaning and mainte-

nance spray (optional accessory).

• Apply an anti-seize compound to all

planing bed surfaces afterwards.

This makes feeding easier and pro-

vides for a smoother surface finish.

7.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation as planer the flat belt (35)

must be positioned as illustrated:

If this is not the case, the flat belt must

be positioned as detailed in chapter

"Surface Planer Mode".

7. Thickness Planer Mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info