Bedienungsanleitung Metabo Multi 260S (Seite 25 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

with a suitable cleaning and mainte-

nance spray (optional accessory).

• Apply an anti-seize compound to all

planing bed surfaces afterwards.

This makes feeding easier and pro-

vides for a smoother surface finish.



Note:

Further information on installation

and operation is found in the operating

instructions supplied with the Drilling and

Morticing Attachment.



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation with the Drilling and Mor-

ticing Attachment the flat belt (45) must

be put on as illustrated:

If this is not the case, the flat belt must

be positioned as detailed in chapter

"Surface Planer Mode".



Caution!

When using the Drilling and

Morticing Attachment the speed of

the chuck must be selected accor-

ding to the mortising bit diameter!

The speed is set by changing the flat

belt:

• small (= rear) motor pulley (48):

spindle speed 3900 min

-1

for mortising bits 10 mm ∅ and up

• large (= front) motor pulley (49):

spindle speed 6300 min

-1

for mortising bits up to 10 mm ∅

To adjust the speed:

1. Open the access door.

2. Loosen lock lever (46) and lift motor

slightly with handle (47).

3. Shfit motor along the axis of the

motorshaft: The motor pulley must

be in alignment with the cutter-

block’s pulley

4. Tighten flat belt by pushing the

motor downward with handle (47).

5. Lock motor in position with the lock

lever (46).

6. Close access door.

Adjusting the cutterblock cover:

7. Adjust cutterblock cover (50) so that

the cutterblock is completely cov-

ered.

9.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation as circular saw the flat belt

(51) must be positioned as illustrated:

If this is not the case, position it as fol-

lows.

1. Open the access door.

2. Loosen lock lever (52) and lift motor

slightly with handle (53).

3. Take the flat belt that is not required

off the motor pulley (54).

4. Tuck the flat belts not required (55)

behind the retaining springs as illus-

trated, so they do not interfere with

the drive belt on the pulleys.

5. Place the flat belt for the saw spin-

dle on the large diameter (front) (51)

motor pulley (54).

6. Shift motor along the axis of the

motor shaft fully to the rear: The

large diameter motor pulley must be

in alignment with the pulley on the

saw spindle.

7. Tighten the flat belt by pushing the

motor downward with the handle

(53).

8. Lock motor in position with the lock

lever (52).

9. Close access door.

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Cutter fence completely dis-

mounted?

2. Cutter spindle fully retracted and

covered by table rings and insert?

3. Cutterblock cover lowered on the

table?

4. Suction port disconnected from the

dust collector and lowered?

Raising the saw blade

1. Remove table insert (56).

2. To raise the saw blade loosen lock

lever (57) and push lever (58) down-

ward. To lock blade at desired depth

of cut tighten lock lever (57) again.

8. Operation With The Drill-

ing And Morticing Attach-

ment (Optional Acces-

sory)

9. Circular Saw Mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info