Bedienungsanleitung Metabo Multi 260S (Seite 24 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Saw blade and blade guard fully

retracted and covered by table

insert?

2. Mitre fence dismounted?

3. Cutter fence completely dis-

mounted?

4. Cutter spindle fully retracted and

covered by table rings and insert?

Dust collection attachment installa-

tion

The dust collection attachment consists

of two parts, the suction port (36) and

the dust chute (37). The duist chute is

attached to a cantilever arm. The suction

port is put on the dust chute.

1. Set infeed table (38) with lever (39)

to 4 mm planing thickness.

2. Swing dust chute over the cutter-

block as illustrated. Both prongs of

the dust chute must fit into the

recesses to the left and right of the

cutterblock.

3. Set infeed table with lever to 0 mm

planing thickness.

4. Connect a suitable dust collector to

the suction port.

7.2 Safety

Safety Devices

• Dust collection attachment

The dust collection attachment (40) pre-

vents that the rotating cutterblock can be

touched when thickness planing.

• Anti-kickback lock

The anti-kickback lock (41) (inside the

planer, not visible) prevents the work-

piece from being thrown back against

the operator by the rotating cutterblock.

All fingers of the anti-kickback lock must

end in a point at their lower end.

All anti-kickback fingers must automati-

cally return to their rest position (down-

wards).

Information for a safe operation

Danger!

Drawing-in/trapping hazard!

− Never reach with your hands into

the machine when guiding the work-

piece!

− Use a feeding aid (push stick) if you

want to feed short stock into the

thicknesser. Stock to be thicknessed

must be at least 200 mm long.

− Guide a workpiece on the outfeed

side if it has been fed so far into the

thicknesser that it can no longer be

safely guided from the infeed side.

− Remove stuck stock only after motor

has come to a complete stop and

the machine is unplugged.



Risk of kickback

Risk of injury by workpiece

kickback (workpiece is caught by the

rotating cutterblock and thrown back

against the operator):

− Do not jam workpieces.

− Operate machine only with a fully

functional anti-kickback lock.

− Always use sharp cutter knives.

− If in doubt check workpiece for inclu-

sion of foreign objects (e.g. nails,

screws, lose knots).

− Always plane the workpiece over its

entire length.

− Do not thickness plane more than

two workpieces at the same time.



Risk of injury by touching the

rotating cutterblock:

− Always cover the cutterblock with

the the dust collection attachment

when the machine is used as thick-

ness planer.

7.3 Operation

1. Loosen locking screw (42) and set

planing thickness with the hand-

wheel (43).

− The thicknesser bed adjusts in a

range from 4 mm to 155 mm.

− One full revolution of the handwheel

moves the thicknesser bed by

4.7 mm.

2. Tighten locking screw (42) again.

3. To thickness plane stock which sur-

faces are not parallel, use suitable

feeding aids (make fitting tem-

plates).

4. The thicknesser feed must be

switched on for thickness planing. If

this is not the case, lift lever (44) and

push it in.

5. Start motor.

6. Assume proper operating position:

to feed the workpiece into the

machine, position yourself offset to

one side of the feed opening.

7. Feed workpiece slowly and straight

into the thicknesser. It will then be

automatically fed through the thick-

nesser.

8. Guide workpiece straight through

the thicknesser.

To remove the workpiece from the

machine, position yourself offset to

one side of the outfeed opening.

9. Switch machine off if no further plan-

ing is to be done immediately after-

wards.

Workpiece dimensions

• Length: min. 200 mm.

• Width: max. 259 mm.

• Thickness: min 4 mm;

max. 155 mm.

Tips and Tricks

• Plane stock with the grain, if possi-

ble.

• Use roller supports on both sides of

the planer/thicknesser when work-

ing long stock.

• When thickness planing it is better

to make several passes with little

chip removal, than making only few

passes with a high depth of cut.

• Keep surfaces of planing beds clean

– in particular, remove resin residue

4243

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info