Bedienungsanleitung Metabo Multi 260S (Seite 26 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

3. Replace the kerf plate. To do so,

slightly bend the table insert apart at

its rear and slide over saw blade

and riving knife. Then fit table insert

flush into the saw table.

Rip fence installation

• Slide fence carrier (59) on the guide

rail (60) and secure with clamping

plate (61).

Mitre fence installation

The mitre fence can be used both in

front of or behind the workpiece.

• When used in front of the

workpiece – especially suitable for

cutting ledges and boards:

• When used behind the workpiece –

especially suitable for cutting

sheets:

1. Loosen screws (62) until fence car-

rier can be pushed in the groove of

the sliding carriage.

2. Set to desired angle and tighten

screws (62).

3. Loosen screws (63), until fence

extrusion can be pushed on the

fence carrier (64).

4. Shift wooden end piece (65) to other

end, if necessary. The end piece

must be fitted on the end of the

fence extrusion that reaches to the

saw blade.



Caution!

The fence extrusion must not

extend into the line of cut!

5. Tighten screws (63).

9.2 Safety

Safety Devices

• Riving knife

The riving knife (66) prevents the work-

piece from being caught by the rising

teeth of the saw blade and being thrown

against the operator.

When sawing, the riving knife must be

positioned at a distance of 3 – 8 mm

from the saw blade

• Blade guard

The blade guard (67) protects against

accidental contact with the saw blade

and from chips flying about.

When using the saw, the blade guard

must alway be positioned so that the dis-

tance between the workpiece and lower

front edge of the blade guard is not more

then 2 mm.

• Push stick

The push stick (68) serves as an exten-

sion of the hand and protects against

accidental contact with the saw blade.

Always use push stick if distance

between

rip fence and saw blade is ≤ 120 mm.

Information for a safe operation



General Hazard:

− Never cut several workpieces at the

same time – and also no bundles

containing several individual pieces.

Risk of personal injury if individual

pieces are caught by the saw blade

uncontrolled.



Risk of kickback

Risk of injury by workpiece

kickback (workpiece is caught by the

rotating saw blade and thrown back

against the operator):

− Do not attempt to stop the saw

blade by pushing the workpiece

against its side.

− Always hold the workpiece down on

the table and do not jam it.

− always work with a properly set riv-

ing knife.

− Always use sharp saw blades. If in

doubt check workpiece for inclusion

of foreign objects (e.g. nails, screws,

lose knots).

Danger!

Drawing-in/trapping hazard!

− Use a feeding aid (push stick) if you

want to cut short stock.

− Never cut stock to which ropes,

cords, strings, cables and wires are

attached or which contains such

materials.

9.3 Operation

1. Set bevel angle:

− Loosen lock lever (69).

− Tilt the sawhead to obtain the

desired bevel angle.

− Tighten lock lever (69) to hold the

saw blade in position.

2. Set depth of cut:

− Loosen lock lever (70) and push

lever (71) down.

− Set desired depth of cut – the dis-

tance between workpiece and

lower front edge of the blade

guard must not be more than

2 mm.

6766

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info