Bedienungsanleitung Metabo Multi 260S (Seite 29 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

7. Use a push block when working the

ends of narrow stock.

8. When working across the grain

(making slots and tenons), use ten-

oning table, stock clamp (92) and

sliding carriage (93).



Note:

Further information on installation

and operation is found in the operating

instructions supplied with the Tenoning

Table.

9. Switch machine off if no further plan-

ing is to be done immediately after-

wards.

Tips and Tricks

• Always make several passes if a

large amount of material needs to

be removed.

• Make trial cuts on a piece of scrap

before working the actual work-

piece.

• When working complex shapes,

make jigs and guides to guide the

workpiece properly.



Danger!

Prior to all servicing:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Replace defective parts, especially of

safety devices with genuine replace-

ment parts only. Parts not tested and

approved by the equipment manufac-

turer can cause unforeseen damage.

After all servicing:

− Check to see that all safety

devices are operational.

− Make sure that no tools or other

parts remain on or in the

machine.

Repair and maintenance work other

than described in this section should

only be carried out by qualified speci-

alists.

11.1 Replacing cutter knives



Note:

Worn cutter knives are noticeable

− reduced planing performance;

− increased risk of kickback;

− motor overloads.



Danger!

Risk of personal injury by cuts

from the cutter knives! Wear gloves

when changing cutter knives.

To remove the cutter knives:

1. Unplug power cable.

2. Remove the fence.

3. Remove the cutterblock cover

4. Turn the three square-head bolts

(94) of the cutter knife lockbar (95)

all the way in (wear gloves!).

5. At first remove cutter knife (96), then

cutter knife lockbar (95) from the

cutterblock (97).

6. In the cutterblock’s groove there are

still two springs. Note exact position

of the springs (for reassembly), then

remove them.

7. Clean all surfaces of cutterblock and

cutter knife lockbar with a suitable

solvent.



Danger!

Do not use cleaning agents

(e.g. to remove resin residue) that

could corrode the light metal compo-

nents; the stability of the light metal

components would be adversely

affected.

To install the cutter knives:



Danger!

− Use only suitable cutter knives

conforming to EN 847-1 (see

"Available Accessories") – unsui-

table, incorrectly mounted, blunt

or damaged cutter knives can

work loose or increase the risk of

kickback considerably respec-

tively.

− Always replace both cutter

knives.

− On the cutterblock and cutter

knife lockbar the numbers "1"

and "2" respectively are punched

in. When reassembling, ensure

that the numbers on cutterblock

and cutter knife lockbar match,

otherwise damage to the bearings

could occur by a balance error.

− Only cutter knives marked "HSS"

or "HS" can be resharpened!

When resharpening, remove the

same amount of material from

both cutter knives, otherwise a

balance error may cause damage

to the bearings.

− Cutter knives can only be reshar-

pened down to a minimum width

of 12 mm.

− Install cutter knives using only

genuine replacement parts.

8. Place spring clips back into their ori-

ginal position in the cutterblock’s

groove.

9. Place the cutter knife lockbar in the

cutterblock’s groove. Turn the three

square-head bolts so far out that the

cutter knife will just slide in.

10. Insert a sharp cutter knife and adjust

position with the cutter knife lockbar,

so that neither protrudes over the

edge of the cutterblock.

11. Place cutter knife setting gauge on

planer bed in the direction as indi-

cated by the arrows in the illustra-

tion:

The setting gauge (98) must rest

with its edge (99) on the front edge

of the infeed table (100).

The pin (101) of the setting gauge

must engage in the cutterblock’s

groove.

The cutter knife (102) must protrude

11. Care and Maintenance

92 93

949596

98 99

100

101

102

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info