Bedienungsanleitung Metabo Multi 260S (Seite 30 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451463

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

so much that it will touch the setting

gauge.

12. To tighten the cutter knife, turn the

three square-head bolts of the cutter

knife lockbar fully out. Start with the

two outer bolts, then tighten the cen-

tre bolt.



Danger!

− Do not extend tool when tighte-

ning the bolts.

− Do not tighten bolts by striking

the wrench.

13. Install the cutterblock guard extru-

sion.

11.2 Saw blade change



Danger!

Directly after cutting the saw

blade can be very hot – burning

hazard! Let a hot saw blade cool

down. Do not clean the saw blade

with combustible liquids.

Risk of injury, even with the blade at

standstill. Wear gloves when chan-

ging blades.

When assembling, the direction of

rotation of the saw blade and outer

flange must be observed!

1. Remove table insert (103).

2. Raise saw blade and lock in posi-

tion.

3. Remove the blade guard (104).

4. Hold the saw spindle with the reten-

tion pin (105) to lock it.

5. Loosen arbor bolt (106) with span-

ner (L.H. thread!).

6. Remove outer blade collar (107),

washer and saw blade from the saw

spindle.

7. Clean clamping surfaces of outer

blade flange and saw blade.



Danger!

Do not use cleaning agents

(e.g. to remove resin residue) that

could corrode the light metal compo-

nents of the saw; the stability of the

saw would be adversely affected.

8. Put on a fresh saw blade (observe

direction of rotation!).



Danger!

Use only suitable saw blades

(see "Technical Specifications") –

when using an unsuitable or dama-

ged blade parts could be explosive-

like hurled from it by centrifugal

forces.

Do not use:

− saw blades made of high speed

steel (HS);

− saw blades with visible damage;

− cut-off wheel blades.



Danger!

− Mount saw blade only using

genuine parts.

− Do not use loose-fitting reducing

rings; the saw blade could work

loose.

− Saw blades have to be mounted

in such way that they do not

wobble or run out of balance, and

can not work loose during opera-

tion.

9. Put on the outer blade flange (107).

10. Screw on arbor bolt (106) with

washer (L.H. thread!) and tighten

hand-tight only.



Danger!

− Do not extend arbor bolt tighte-

ning wrench.

− Do not tighten arbor bolt by stri-

king the wrench.

− After tightening the arbor bolt do

not forget to remove the retention

pin!

11. Replace table insert (103) flush with

the table top.

12. Install blade guard (104).

11.3 Care and maintenance



Danger!

The checks and procedures

described here are meant to help ope-

rate the machine safely! Should there

be faults evident on any of these com-

ponents, the machine must not be

used until these faults have been

remedied in a workmanlike manner.

Before starting any work

1. Check power supply cable for dam-

age, if necessary have replaced by

a qualified electrician.

2. Remove sawdust and chips.

3. Check cutter knives for:

− tight seat

− sharpness

− general condition

(no notches etc.)

4. Check the thicknesser’s anti-kick-

back lock:

− mobility of anti-kickback fingers

(must fall down by their own

weight)

− points of anti-kickback fingers

(not rounded)

5. Check circular saw:

− Distance saw blade – riving knife

OK? (3 – 8 mm)

− Riving knife and blade guard

undamaged?

6. Check spindle moulder:

− Cutter guard undamaged?

Weekly:

1. Remove chips and dust with dust

collector or brush from:

− thicknesser bed spindles;

− height setting mechanism of the

cutter spindle;

− height setting mechanism of the

circular saw;

− adjustment elements of the circu-

lar saw;

− telescopic type ball bearing trav-

eller and track of the sliding car-

riage.



Caution!

Do not spray care and mainte-

nance spray on flat belts and pulleys

– this will cause the flat belt to slip.

2. Apply a light coat of anti-seize com-

pound to infeed table, outfeed table

and thicknesser bed.

11.4 Machine Storage



Danger!

Store machine so that

− it can not be started by unauthori-

zed persons and

− nobody can get injured while the

machine is switched off.



Caution!

Do not store machine unpro-

tected outdoors or in damp environ-

ment.

103

104

105

107

106

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 260S Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info