Bedienungsanleitung Metabo Multi 310G (Seite 26 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

2. Make a test pass with the sliding

carriage (motor OFF, without stock):

The guard plate must always stay

clear of the cutter by at least 10 mm.

9.2 Safety

Safety Devices

• Safety switches

A safety switch prevents the cutter spin-

dle from being driven while the lock pin

is engaged in the cutter spindle or the

drive guard hood is opened.

• Cutter fence with lateral pressure

shoe

The cutter fence and lateral pressure

shoe provide a support for the safe guid-

ing of the workpiece, protect against

accidental contact with the cutter and

chips flying about.

• Guard plate

The guard plate protects against acci-

dental contact with the cutter.

Information for a safe operation



General Hazard:

− Install only suitable cutters. A cutter

must correspond to EN 847-1 and

carry the follwing markings:

− "HAND FEED"

− "MAN".

The installation of grinding or polish-

ing disks is not permissible.

− Before switching on check to see

that the tool is securely clamped.

− Before switching on check to see

that the tool can turn freely. To do

so, turn tool carefully by hand –

Caution – cutting hazard!

− Always work one workpiece at a

time.

− Depending on the job use suitable

safety devices, which prevent unin-

tentional contact with the rotating

cutter. Adapt these safety devices

exactly to the respective application

and the workpiece dimensions.

− Use a feeding aid if you are going to

work a workpiece less than 300 mm

long.

− Always feed the workpiece against

the cutter’s direction of rotation.



Risk of kickback!

Workpiece is caught by the

rotating cutter and thrown back

against the operator:

− Always use sharp cutters only.

− If in doubt check workpiece for inclu-

sion of foreign objects (e.g. nails,

screws, lose knots).

− Depending on the job use suitable

safety devices, which prevent unin-

tentional contact with the rotating

cutter. Adapt these safety devices

exactly to the respective application

and the workpiece dimensions.

− Adapt spindle speed to the cutter

diameter.

9.3 Operation

1. Depending on job, install and adapt

cutter, cutter fence, lateral pressure

shoe and/or guard plate.

Also use sliding carriage, G-cramps

or table extension, if necessary.

2. Adjust spindle speed relevant to the

cutter diameter.

3. Set operating mode selector to spin-

dle moulder mode.

4. Start motor.

5. Assume proper operating position:

6. Loosen locking screw (69) and set

cutting height with handwheel (70)

(any possibly fitted auxiliary fence

will be cut by this process). Tighten

locking screw (69).



Note:

The auxiliary fence is a wearing

part. It is therefore necessary to fabri-

cate a new auxiliary fence if the clear-

ance zone around the cutter has

enlarged the extent that the workpiece

can no longer be safely guided.

7. Work the workpiece.

8. Use a push block when working the

ends of narrow stock.

9. When working across the grain

(making slots and tenons), use ten-

oning table, stock clamp (71) and

sliding carriage (72).



Note:

Further information on installation

and operation is found in the operating

instructions supplied with the Tenoning

Table.

10. Switch machine off if no further plan-

ing is to be done immediately after-

wards.

Tips and Tricks

• Always make several passes if a

large amount of material needs to

be removed.

• Make trial cuts on a piece of scrap

before working the actual work-

piece.

• When working complex shapes,

make jigs and guides to guide the

workpiece properly.



Danger!

Prior to all servicing:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Replace defective parts, especially of

safety devices with genuine replace-

ment parts only. Parts not tested and

approved by the equipment manufac-

turer can cause unforeseen damage.

10. Care and Maintenance

71 72

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info