Bedienungsanleitung Metabo Multi 310G (Seite 27 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

After all servicing:

− Check to see that all safety

devices are operational.

− Make sure that no tools or other

parts remain on or in the

machine.

Repair and maintenance work other

than described in this section should

only be carried out by qualified speci-

alists.

10.1 Replacing Cutter Knives



Note:

Worn cutter knives are noticeable

− reduced planing performance;

− increased risk of kickback;

− motor overloads.



Danger!

Risk of personal injury by cuts

from the cutter knives! Wear gloves

when changing cutter knives.

To remove the cutter knives:

1. Unplug power cable.

2. Remove the fence.

3. Remove the cutterblock cover.

4. Loosen locking screw (73) and raise

outfeed table (74) fully with the regu-

lating screw (75).

5. Turn the four square-head bolts (76)

of the cutter knife lockbar (77) all the

way in (wear gloves!).

6. At first remove cutter knife (78), then

cutter knife lockbar (77) from the

cutterblock (79).

7. In the cutterblock’s groove there are

still two springs. Note exact position

of the springs (for reassembly), then

remove them.

8. Clean all surfaces of cutterblock and

cutter knife lockbar with a suitable

solvent.



Danger!

Do not use cleaning agents

(e.g. to remove resin residue) that

could corrode the light metal compo-

nents; the stability of the light metal

components would be adversely

affected.

To install the cutter knives:



Danger!

− Use only suitable cutter knives

conforming to EN 847-1 (see

"Available Accessories") – unsui-

table, incorrectly mounted, blunt

or damaged cutter knives can

work loose or increase the risk of

kickback considerably respec-

tively.

− Always replace all cutter knives.

− On the cutterblock and cutter

knife lockbar the numbers "1"

and "2" and "3" respectively are

punched in. When reassembling,

ensure that the numbers on cut-

terblock and cutter knife lockbar

match, otherwise damage to the

bearings could occur by a

balance error.

− Only cutter knives marked "HSS"

or "HS" can be resharpened!

When resharpening, remove the

same amount of material from all

cutter knives, otherwise a

balance error may cause damage

to the bearings.

− Cutter knives can only resharpe-

ned to a minimum width of

12 mm.

− Install cutter knives using only

genuine replacement parts.

9. Place spring clips back into their ori-

ginal position in the cutterblock’s

groove.

10. Place the cutter knife lockbar in the

cutterblock’s groove. Turn the four

square-head bolts so far out that the

cutter knife will just slide in.

11. Insert a sharp cutter knife and adjust

position with the cutter knife lockbar,

so that neither protrudes over the

edge of the cutterblock.

12. Set cutter knife setting gauge (80)

as illustrated in direction of arrows

on the outfeed table (81);

The setting gauge must rest with its

edge (82) against the front edge of

the infeed table.

13. Adjust position of cutter knife (83):

The setting is correct when the cut-

ter knife, at the highest point, barely

touches the setting gauge.

14. Make adjustment at both ends of the

cutter knife.

15. To tighten the cutter knife, turn the

four square-head bolts of the cutter

knife lockbar fully out. Start with the

two outer bolts, then tighten the cen-

tre bolts.



Danger!

− Do not extend tool when tighte-

ning the bolts.

− Do not tighten bolts by striking

the wrench.

16. Install the cutterblock guard extru-

sion.

10.2 Saw blade change



Danger!

Directly after cutting the saw

blade can be very hot – burning

hazard! Let a hot saw blade cool

down. Do not clean the saw blade

with combustible liquids.

Risk of injury, even with the blade at

standstill. Wear gloves when chan-

ging blades.

When assembling, the direction of

rotation of the saw blade and outer

flange must be observed!

1. Remove table insert (84).

2. Lift saw blade up and lock in posi-

tion.

3. Remove the blade guard (85).

4. Hold the saw spindle with the reten-

tion pin (86) to lock it.

767778

80 82

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info