Bedienungsanleitung Metabo Power 180-5 W OF (Seite 10 von 56) (Alle Sprachen)

625656

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISHen

Danger!

Repair of tools must be carried out by qualified

electricians only!

If you have Metabo devices that require repairs,

please contact your Metabo service centre. See

www.metabo.com for addresses.

You can download a list of spare parts from

www.metabo.com.

Danger!

The condensed water from the pressure vessel

contains oil residue and /or contaminations

hazardous to the environment. Dispose of the

condensed water in an environmentally-friendly

manner using respective collection sites!

Observe national regulations on environmentally

compatible disposal and on the recycling of

disused machines, packaging and accessories.

Only for EU countries: Never dispose of

devices in your household waste! In

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment

and its implementation in national legal systems,

used devices must be collected separately and

returned for environmentally compatible

recycling.

Danger!

Prior to all servicing:

Switch machine off. Disconnect the mains plug.

Wait until the device has stopped. Ensure that

there is no more pressure on the device and all

used compressed air tools and accessories.

Leave the device and all used compressed air

tools and accessories to cool down.

Any works other than the ones described in this

chapter, must be carried out only by a qualified

electrician or the service branch in your country.

After to all servicing:

Put back into operation and check all safety

installations. Ensure that there are no tools or

similar at or in the device.

Compressor does not run:

▪ No mains voltage.

– Check cables, plug, outlet and mains fuse.

▪ Mains voltage too low.

– Use only extension cables with sufficient core

cross-section (see chapter 12. Technical

Data). For cold device: Avoid extension cable.

For cold device: Depressurise the pressure

vessel.

▪ Compressor was switched off by pulling the

mains plug while it was running.

– First, switch off the compressor using the ON/

OFF switch (9), then switch on again.

▪ Motor overheated, e.g. due to insufficient

cooling (cooling ribs covered).

– Switch off the compressor using the ON/OFF

switch (9) .

– Remedy the cause for overheating. Leave to

cool for about ten minutes.

– Switch on the compressor again using the ON/

OFF switch (9) .

Compressor runs without building up

sufficient pressure.

▪ Condensate outlet leaking.

– Ensure that the condensate outlet (3) is

closed.

– Check the seal of the drainage plug, if

required, replace.

▪ Check valve leaking.

– Have check valve serviced in authorised

service centre.

Compressed air tool does not get enough

pressure.

▪ Pressure controller not open enough.

– Open pressure controller (7) further.

▪ Hose connection between compressor and

compressed air tool leaking.

– Check hose connection; if required replace

damaged parts.

Explanatory notes on the specifications on page 3.

Changes due to technological progress reserved.

A =suction capacity

F =filling capacity

eff

=Effective output volume at 80% max.

pressure

p = max. pressure

V =vessel size

a =number of air outlets

z =number of cylinders

=max. torque

=rated input power

U=connection voltage

I=rated power

F =min. fuse protection

IP =protection class

G =maximum overall length and core cross-

section of extension cables

A =dimensions (lxwxh)

max

=max. storage / operating temperature *

min

=min. storage / operating temperature **

m=weight

* = The service life of some components e.g. seal

in check valve is significantly reduced, if the

compressor is operated at high temperatures

(max. storage / operating temperature and higher).

** = At temperature below the min. storage /

operating temperature, there is danger of frost for

the condensate in the pressure vessel.

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Emission values

These values make it possible to assess the

emissions from the device and to compare

different devices. The actual load may be higher or

lower depending on the operating conditions, the

condition of the device or the accessories. Please

allow for breaks and periods when the load is lower

for assessment purposes. Arrange protective

measures for the user e.g. organisational

measures based on the adjusted estimates.

Typical A-effective perceived sound levels

=sound-pressure level

=acoustic power level

WA(G)

=guaranteed acoustic power level as per

2000/14/EC

, K

=uncertainty

Wear ear protectors!

Information on the nameplate:

A Manufacturer

B Item, version, serial number

C Machine designation

D Connection voltage / frequency

E Rated input power

F Rated power / protection type

G Max. torque

H Max. pressure

I CE mark – This machine conforms to the EC

directives as per Declaration of Conformity

J Year of manufacture

K Suction capacity

L Filling capacity

M Compressor speed

N Number of cylinders

O Boiler size

P Disposal symbol (see chapter 10.)

9. Repairs

10. Environmental Protection

11. Troubleshooting

12. Technical Data

1~ 230 V 50 Hz

P 1,50 kW S 3

I = 6,0 A IP 20

01532XX0 9998812345

Basic 250-24 W OF

-1

2850 min

220 l/min

120 l/min

2850 min

24 l

-1

YYYY

8 bar / 116 psi

Metabo Power 180-5 W OF Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info