Bedienungsanleitung Metabo RF 14-115 (Seite 10 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600618

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISHen

Original instructions

Under our sole responsibility, we hereby declare

that these renovation routers, identified by type and

serial number *1), comply with all relevant

requirements of the directives *2) and standards *3)

and technical documents for *4) - see Page 3.

When fitted with original Metabo accessories, the

machine is suitable for the following tasks:

... Removing plaster, old tile adhesive and

paintwork,

... Milling off formwork transitions,

... Roughing concrete surfaces

Also suitable for grinding surfaces with diamond

cup wheels

Do not use for abrasive cutting-off operations,

roughing work, sanding, polishing or flap disc work.

The machine must not be used with water.

It is suitable for commercial use in trade and

industry.

Always use a suitable dust extraction system:

Connect an M-class vacuum cleaner to the

extractor connection piece (1).

The user bears sole responsibility for any damage

caused by improper use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

For your own protection and for the

protection of your power tool, pay

attention to all parts of the text that are

marked with this symbol!

WARNING – Reading the operating

instructions will reduce the risk of injury.

WARNING Read all safety warnings and

instructions. Failure to follow all safety

warnings and instructions may result in electric

shock, fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Pass on your electrical tool only together with these

documents.

General safety instructions for routing and

grinding:

Use

a) This power tool is designed for surface

routing and grinding. Refer to all

safety

warnings,

instructions, illustrations and

specifications provided with this power tool.

Failure to follow all the instructions may result in

electric shock, fire and/or serious injury.

b) This power tool is not suitable for polishing

or tasks using roughing discs, wire brushes,

parting grinder discs and flap discs. Operations

for which the power tool was not designed may

create a hazard and cause personal injury.

c) Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. The simple fact that an

accessory can be attached to your power tool does

not ensure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately protected or

controlled.

f) The arbour size of routing tools, flanges,

diamond cup wheels or any other accessory

must properly fit the spindle of the power tool.

Accessories with arbour holes that do not match the

mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of

control.

g) Do not use a damaged accessory. Before

use, always check accessories for splinters or

cracks and check grinding wheels for cracks or

signs of severe wear and tear. If a power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute. Damaged accessories will normally break

apart during this test time.

h) Wear personal protective equipment.

Depending on application, use a face shield,

safety goggles or safety glasses. As

appropriate, wear a dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by

various operations. The dust mask or respirator

must be capable of filtering particles generated by

your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

your work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of a workpiece or broken accessory may

fly into the air and cause injury beyond the

immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

1. Declaration of Conformity

2. Specified Use

3. General safety instructions

4. Special Safety Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo RF 14-115 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info