Bedienungsanleitung Metabo RF 14-115 (Seite 11 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600618

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH en

where the cutting accessory may contact

hidden wiring or its own cord. A cutting

accessory that comes in contact with a "live" wire

may render exposed metal parts of the power tool

"live" and give the operator an electric shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be cut

or snagged and your hand or arm may be pulled into

the spinning accessory.

I) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may catch the surface and pull

the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan draws dust into the housing.

o) Do not operate the power tool near

flammable materials. Sparks could ignite these

materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

4.1 Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged routing or grinding tool or similar

accessory. Pinching or snagging causes the

rotating accessory to come to an abrupt halt, which

in turn forces the uncontrolled power tool in the

direction against the accessory’s rotation at the

point of jamming.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions. It can

be avoided by taking proper precautions as given

below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use the auxiliary

handle, if provided, maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your for hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the power tool in the direction

against the accessory’s movement at the point of

jamming.

d) Use special care when working around

corners, sharp edges etc. Avoid bouncing and

snagging the accessory. The rotating accessory

tends to jam around corners and sharp edges and

also if bouncing occurs, thus causing loss of control

or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades create

frequent kickback and loss of control.

4.2 Safety Warnings Specific for Routing

Operations:

a) Use only routing tools that are

recommended for your power tool and the

specific guard designed for these routing

tools. Routing tools that are not designed for use

with the power tool cannot be guarded properly and

are unsafe.

b) The guard must be securely attached to the

power tool and positioned so as to minimise

exposure of the routing body to the operator

and thus maximise safety.

The guard helps to

protect the operator from broken fragments,

accidental contact with the routing body and sparks

that could ignite clothing.

c) Do not work on surfaces with exposed steel

reinforcements or similar. Doing so may result in

kickback or loss of control over the power tool.

d) Before commissioning, check that the

routing wheels can move freely. Clean these, if

necessary.

e) Do not use damaged routing wheels.

f) Exercise particular caution when working on

corners, edges and ledges. There is a risk here of

kickback or damaging the router.

g) Routing wheels have sharp edges and may

be very hot after use. Caution! Risk of injury.

4.3 Safety Warnings Specific for Grinding

with Diamond Cup Wheels:

a) Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot be

adequately guarded and are unsafe.

b) The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed

towards the operator. The guard helps to protect

the operator from broken fragments, accidental

contact with the wheel and sparks that could ignite

clothing.

c) Wheels must be used only for recommended

applications.

d) Always use undamaged wheel flanges that

are the correct size and shape for your selected

accessories. The correct flanges support the

accessories.

4.4 Additional Safety Instructions

WARNING – Always wear protective

goggles.

Wear a suitable dust protection mask.

Observe the specifications of the accessory

manufacturer! Protect the accessories from grease

and physical impact.

Accessories must be stored and handled with care

in accordance with the manufacturer's instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo RF 14-115 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info