Bedienungsanleitung Metabo RF 14-115 (Seite 13 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600618

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH en

6.3 Dust extraction

Always use a suitable dust extraction system:

Connect an M-class vacuum cleaner to the

extractor connection piece (1).

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle must be at a standstill.

7.1 Locking the spindle

Press in the spindle locking knob (9) only

when the spindle is stationary!

- Press in the spindle locking button (9) and turn the

spindle (8) by hand until you feel the spindle

locking button engage.

7.2 Fitting/removing the routing tool

For safety reasons, use the safety guard (19)

with the attached depth stop (22).

See illustration B on page 2.

To fit:

- Lock the spindle (see chapter 7.1).

- Screw on and tighten the routing tool (7) using the

2-hole spanner (6) in a clockwise direction.

To remove:

- Lock the spindle (see chapter 7.1). Unscrew the

routing tool (7) with the 2-hole spanner (6) in an

anticlockwise direction.

7.3 Fitting/removing the diamond cup wheel

For safety reasons, use the safety guard (19)

with the attached depth stop (22).

See illustration C on page 2.

To fit:

- Fit the support flange (12) on the spindle. (8) The

flange should not turn on the spindle when

properly attached.

- Lay the diamond cup wheel (11) on the support

flange (12) so that it lies flat along the support

flange.

- The 2 sides of the clamping nut (10) are different.

Screw the clamping nut onto the spindle so that

the band of the clamping nut (10) is facing upward.

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (10) clockwise using the 2-hole

spanner (6) to secure.

To remove:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (10) anticlockwise using the 2-hole

spanner (6) to unscrew.

8.1 Setting speed

Set the optimum speed on the setting wheel (18),

depending on the application.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

Machines with slide switch:

Switching on: Push the slide switch (15) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (15) and release.

Replace worn or damaged routing wheels (see

figure, page 2):

- Removing the routing tool (see chapter 7.2).

- Extract the screw (13) in an anticlockwise

direction. Remove the safety disc (14).

- Replace all routing wheels as shown.

(Always use the same type of routing wheels).

-Reassemble all parts as shown.

Insert and turn the screw (13) in a clockwise

direction and tighten with 7 Nm ± 1 Nm.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. The machine must be

held firmly in this case.

The electronic signal display (17) lights

up and the load speed decreases. The coil

temperature is too high! Run the machine in

idling until the electronics signal indicator switches

off.

The electronic signal display (17) flashes

and the machine does not start. The restart

protection is active. If the mains plug is

inserted with the machine switched on, or if the

current supply is restored following an interruption,

the machine does not start up. Switch the machine

off and on again.

7. Attaching the accessory

8. Use

9. Maintenance

10. Cleaning

11. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo RF 14-115 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info