Bedienungsanleitung Metabo RS 17-125 (Seite 12 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600619

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISHen

To remove:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (7) anticlockwise using the 2-hole

spanner (6) to unscrew.

8.1 Working close to walls

To open and close the segment: switch off the

machine and pull the mains plug. The acces-

sory must be stationary.

Only raise the segment (13) when working

close to walls. Otherwise, the segment must

be lowered.

The open area of the safety guard must face the

direction of the wall.

8.2 Setting the speed (RS 14-125)

Set the optimum speed on the setting wheel (20),

depending on the application.

A wheel setting of between 4 and 6 is suitable for

most applications.

8.3 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only set it

down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate on the work.

RS 14-125:

Switching on:

Push the slide switch (18) forward.

For continuous activation, now tilt down-

wards until it engages.

Switching off:

Press the rear end of the slide switch

(18) and release.

RS 17-125:

Momentary activation

Switching on:

Press in lock (16) and then press

trigger (17). Release the lock (16).

Switching off:

Release the trigger (17).

Continuous operation:

Switching on:

Press in lock (16) and hold in. Press

and hold in trigger (17). The machine is now

switched on. Now release the trigger (17).

Then release the lock (16) to hold the trigger

in position and prevent deactivation

(continuous operation).

Switching off:

Press the trigger (17) and release.

Motor cleaning: The machine must be vacuumed

regularly, frequently and thoroughly through the

ventilation slots using a suitable vacuum cleaner.

The machine must be held firmly in this case.

Replacing the spring-mounted ring brush:

Replace worn brushes for optimal dust extraction.

Replacement brush set: Order No. 6.28214.

RS 14-125:

The electronic signal display (19) lights

up and the load speed decreases. The coil

temperature is too high! Run the machine in

idling mode until the electronics signal indicator

switches off.

The electronic signal display (19) flashes

and the machine does not start. The restart

protection is active. If the mains plug is

inserted with the machine switched on, or if the

current supply is restored following an interruption,

the machine does not start up. Switch the machine

off and on again.

RS 17-125:

- Restart protection: If the mains plug is inserted

with the machine switched on, or if the current

supply is restored following an interruption, the

machine does not start up. Switch the machine off

and on again.

- Overload protection: There is a reduction in

load speed. The coil temperature is too high!

Allow the machine to run at idle speed until it has

cooled down.

- Switching on the machine reduces the voltage

briefly. Unfavourable mains power conditions may

have a detrimental effect on other machines.

Network impedances less than 0.4 ohms should

not cause malfunctions.

Use only genuine Metabo accessories.

Use only accessories that fulfil the requirements

and specifications listed in these operating instruc-

tions.

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

8. Use

9. Cleaning, Maintenance

10. Troubleshooting

11. Accessories

12. Repairs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo RS 17-125 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info