Bedienungsanleitung Metabo SB 660 (Seite 14 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

511032

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

ENG

inside the drill chuck (if applicable / model-

specific). Caution left-handed thread !

(see Section 8.13.)

7.1 Side handle installation

For safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(16) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (4).

Tighten the side handle in the required angle

depending on the task at hand.

8.1 Depth stop setting

Loosen the side handle (16). Set depth stop (4) to

the desired drilling depth and retighten the side

handle.

8.2 Switching on/off

To start the machine, press the trigger (13).

The speed can be changed at the trigger

(not SB 660).

Due to the electronic soft start the machine

accelerates continuously up to the pre-selected

speed (SBE 1010 Plus, SBE 85, SBE 850 Impuls,

SBE 850 Contact).

For continuous operation the trigger can be locked

with the lock button (11). To stop the machine,

press the trigger again.

If switched on continuously, the machine

continues running if it is jerked out of your

hands. Therefore, always hold the machine

with both hands on the handles, stand safely,

and concentrate on your work.

8.3 Speed preselection

(not for SB 660)

Pre-select the max. speed with the preselection

wheel (12). See page 4 for recommended drilling

speeds.

8.4 Gear selection

Select the desired gear by turning the control

knob (5).

Change gears only with the machine coming to a

complete standstill (start and switch right off

again).

1. gear

(low speed, high torque)

e.g. for screwing twist drilling

2. gear

(high speed) e.g. for twist drilling,

impact drilling

8.5 Changing between twist drilling/impact

drilling

Select desired operating mode by shifting the slide

switch (6) as required.

Twist drilling

Impact drilling

Use high speed for impact drilling. Set control

knob (5) to .

Impact and twist drilling can be done only with a

clockwise direction of rotation.

8.6 Selection of direction of rotation

(not for SB 660)

Do not actuate the rotation selector

switch (14) unless the motor has

completely stopped.

Select direction of rotation:

R = clockwise

L = counter-clockwise

The drill chuck must be firmly screwed

onto the spindle and the safety screw

inside the drill chuck (if applicable / model-

specific) must be firmly tightened with a

screwdriver. (Caution, left-handed thread !) If

rotated counterclockwise (e.g. when screwing)

it could otherwise become loose.

8.7 Tool change with Futuro Top keyless

chuck (3)

Insert tool. Grip the retaining ring (a) firmly and,

with the other hand, turn the sleeve (b) against the

stop. To open the drill chuck grip the retaining ring

8Use

17026951_0709 SB_Bauk.book Seite 14 Montag, 13. Juli 2009 1:54 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo SB 660 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info