511032
15
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
ENGLISH
15
ENG
(a) firmly and turn sleeve (b) in the opposite
direction.
8.8 Tool change with Futuro Plus keyless
chuck (2)
Insert tool. Grip the retaining ring (a) firmly and,
with the other hand, turn sleeve (b) towards GRIP,
ZU", until the mechanical resistance which can be
felt is overcome.
Caution! The chuck is not yet fully tightened!
Keep turning
(there is a clicking" sound while
turning)
, until further turning is no longer possible -
only now
is the tool
securely
tightened.
When using soft bit shanks, it may be necessary to
retighten the chuck after a short period of
operation.
Opening the drill chuck:
Grip the retaining ring (a) firmly and, with the other
hand, turn the sleeve (b) towards AUF, RELEASE".
Note:
The ratchet sound which can possibly be
heard after opening the drill chuck, is functional and
is switched off by a reverse rotation of the sleeve.
If the tool is fitted very tight:
Unplug. Hold drill chuck with an open end spanner
at the jaw opening and turn sleeve (b) firmly
towards "AUF, RELEASE".
8.9 Tool change with geared chuck (1)
Fitting the tool:
Insert the tool and tighten evenly with chuck key in
all three 3 holes.
Removing the tool:
Open the geared chuck with the chuck key and
remove tool.
8.10 Contact mode
(SBE 850 Contact)
To enable the contact mode press button (8).
If required, e.g. for drilling into steel girders or
steel-reinforced concrete walls, the contact mode
can be disabled by pressing the switch button (8).
The contact mode indicator (7) shows the current
setting:
Green:contact mode enabled.
Red: machine has switched off because contact
was made with conductive, earthed
material or a live supply cable.
Pull machine back and bit out of the hole
immediately. Have possible damage
properly repaired.
Off: contact mode disabled.
8.11 Pulse function
(SBE 85, SBE 850 Impuls)
Adjust via the thumbwheel (9).
Pulse function constantly switched On
+ Pulse function Off (for drilling)
Recommended settings for screwdriving, for
example, into wood (soft screwdriving)::
8.12 Torque limiter
(SBE 85, SBE 850 Impuls)
Upon attainment of the preselected torque the
motor comes to a standstill. Adjust via the
thumbwheel (9). (positions 1 - 6).
1 Upon attainment of a low torque the motor
comes to a standstill.
a
b
3x
ø
4,0
B2
4,5
B3
5,0
C3
6,0
C4
8,0
D5
17026951_0709 SB_Bauk.book Seite 15 Montag, 13. Juli 2009 1:54 13
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo SB 660 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info