Bedienungsanleitung Metabo SM 5-55 (Seite 12 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595109

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

ENG

screwdriver bit: turn the adjusting ring (9) clock-

wise.

•

To decrease the protrusion distance of the

screwdriver bit: turn the adjusting ring (9) anti-

clockwise.

Fine adjustment is performed after the tool is

tested. See section 7.3.

The magazine screw attachment is now ready for

operation.

See illustration on page 3 (please unfold).

7.1

Inserting / Removing a screw strip

(11)

Check whether the screw heads are resting

on the plastic strip otherwise the strip guide

(12) may become damaged and no longer function

correctly.

The screw strip (11) can be inserted from either

side.

- Feed the screw strip (11) through the strip guide

(12).

- Then guide the holes on the strip over the tips of

the teeth on the ratchet wheels (10)

until the

first screw is located in the position in front of

the insertion position

. The screwdriver bit (3)

picks up this screw when the depth stop (7) is

pushed down. For this reason, do not push the

screw strip (11) in too far to avoid wasting any

screws.

To remove the screw strip (11), pull forwards

through the tool. Do not pull the screw strip

(11) back as this may cause serious damage.

7.2 Machine use

We recommend:

- setting the screwdriver to clockwise rotation.

- setting the screwdriver to run continuously.

- Hold the screwdriver with one hand (as shown in

the illustration on page 3). Hold the handle (13)

with the other hand if necessary.

- Hold the tool at right angles to the work surface.

The screw will not be inserted far enough if the

tool is held at an angle that deviates from 90°

even slightly.

- Rest the depth stop (7) on the screwdriver

magazine against the workpiece and apply pres-

sure.

- The screw moves to insertion position and is

screwed into the workpiece.

- If the coupling on the screwdriver audibly disen-

gages, remove the magazine screw attachment

from the workpiece.

7.3 Precision screw depth adjustment

The screw depth (or countersink depth) is adjusted

by turning the adjusting ring (9).

- Insert a screw to test the tool settings.

- If necessary, fine adjust the countersink depth by

turning the adjusting ring (9):

•

To increase the protrusion distance of the

screw head: turn the adjusting ring clockwise.

•

To decrease the protrusion distance of the

screw head: turn the adjusting ring anticlock-

wise.

7.4 Changing the screwdriver bit (3)

Always use genuine Metabo screwdriver bits (see

section 10 Accessories).

If the screwdriver bit is worn/damaged or a

different fastening system is used (Philips,

Pozidriv, Torx or Square Drive), the screwdriver bit

must be changed.

- Detach the screwdriver magazine with adapter

(2) from the screwdriver (do not slacken the

clamping screw (1)).

- Remove the screwdriver bit (3) (read the screw-

driver Operating Instructions).

- Insert a new screwdriver bit (3) (read the screw-

driver Operating Instructions)

- Attach the screwdriver magazine with adapter (2)

to the screwdriver again.

See illustration on page 3 (please unfold).

Problems:

•

Countersink depth: see points b), d), e), i)

•

Seized screws: see point b)

•

Missing screws: see points c), g)

•

Screws do not move: see points a), d)

•

Sliding piece (6) not fully inserted: see point h)

• General: see points a) to i)

Troubleshooting:

a) Always set the screwdriver to CLOCKWISE

ROTATION (FORWARDS).

b) Make sure that the depth stop (7) is adapted to

the length of the screws used.

c) The screwdriver bit (3) must be the correct

length. Always use genuine Metabo screwdriver

bits (see section 10 Accessories).

d) If you are working with Philips screws, make

sure you use a Philips screwdriver bit. If you are

working with Pozidriv screws, make sure you

7Use

8 Troubleshooting

17026885_1211 SM 5-55.book Seite 12 Mittwoch, 14. Dezember 2011 11:28 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo SM 5-55 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info