Bedienungsanleitung Metabo TS 254 (Seite 18 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

633940

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

ENGLISH

 Turn power off if the tool is not used.

Cutting hazard, even with the

cutting tool at standstill!

 Wear gloves when changing cutting

tools.

 Store saw blade in such manner that

nobody will get hurt.

Risk of kickback (workpiece is

caught by the saw blade and thrown

against the operator):

 Always work with a properly set riv-

ing knife.

 The riving knife and the saw blade

used must match: the riving knife

should be thinner than the kerf, but

thicker than the saw blade body.

 Do not jam workpieces.

 Make sure the saw blade is suitable

for the workpiece material.

 Cut thin or thin-walled workpieces

only with fine-toothed saw blades.

 Always use sharp saw blades.

 If in doubt, check workpiece for in-

clusion of foreign matter (e.g. nails

or screws).

 Cut only stock of dimensions that al-

low for safe and secure holding

while cutting.

 Never cut several workpieces at the

same time – and also no bundles

containing several individual pieces.

Risk of personal injury if individual

pieces are caught by the saw blade

uncontrolled.

 Remove small cutoffs, scrap, etc.

from the work area – when doing so

the saw blade must be at a complete

standstill.

Drawing-in/trapping hazard!

 Ensure that no parts of the body or

clothing can be caught and drawn in

by rotating components (no neck-

ties, no gloves, no loose-fitting

clothes; contain long hair with hair-

net).

 Never attempt to cut any workpieces

which contain

–ropes,

–strings,

–cords,

– cables or

– wires, or to which any of the

above are attached.

Hazard generated by insuffi-

cient personal protection gear!

 Wear hearing protection.

 Wear protective goggles.

 Wear dust mask.

 Wear suitable work clothes.

 When working outdoors wearing of

non-slip shoes is recommended.

 Wear gloves when handling saw

blades and rough workpieces. Car-

ry saw blades in a container.

Risk of injury by inhaled wood

dust!

 Dust of certain timber species (e.g.

beech, oak, ash) can cause cancer

when inhaled. Work only with a suit-

able dust collector attached to the

saw. The dust collector must comply

with the data stated in the technical

specifications.

 Ensure that as little as possible

wood dust will get into the environ-

ment:

– remove wood dust deposit in the

work area (do not blow away!);

– fix any leakages on the dust col-

lector;

– ensure good ventilation.

Hazard generated by modifica-

tion of the machine or use of parts

not tested and approved by the

equipment manufacturer!

 Assemble tool in strict accordance

with these instructions.

 Use only parts approved by the

equipment manufacturer. This ap-

plies especially for:

– saw blades (for order numbers,

refer to Available Accessories);

– safety devices (for order num-

bers, see spare parts list spare

parts list).

 Do not change any parts.

Hazard generated by tool de-

fects!

 Keep tool and accessories in good

repair. Observe the maintenance in-

structions.

 Before every use check tool for pos-

sible damage: before operating the

tool all safety devices, protective

guards or slightly damaged parts

need to be checked for proper func-

tion as specified. Check to see that

all moving parts work properly and

do not jam. All parts must be cor-

rectly installed and meet all condi-

tions necessary for the proper oper-

ation of the tool.

 Damaged protection devices or

parts must be repaired or replaced

by a qualified specialist. Have dam-

aged switches replaced by a service

centre. Do not operate tool if the

switch cannot be turned ON or OFF.

 Keep handles free of oil and grease.

Risk of injury by noise!

 Wear hearing protection.

 Make sure the riving knife is not

bent. A bent riving knife will push the

workpiece against the side of the

saw blade, causing noise.

Danger from blocking work-

pieces or workpiece parts!

If blockage occurs:

1. switch machine off,

2. unplug mains cable,

3. wear gloves,

4. clear the blockage using a suitable

tool.

3.3 Symbols on the machine

Information on the nameplate:

(25) Manufacturer

(26) Serial number

(27) Machine designation

(28) Motor specifications

(see also "Technical specifica-

tions")

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TS 254 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info