Bedienungsanleitung Metabo TS 254 (Seite 22 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

633940

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

ENGLISH

3. Lock the set bevel tilt by tightening

the lock lever (48).

Handwheel for cutting depth

adjustment

The depth of cut can be adjusted by

turning the handwheel (49).

Lock lever for bevel angle adjust-

ment

By releasing the lock lever (50), the saw

blade can be adjusted between -1.5°

and 46.5°.

To keep the set bevel angle from chang-

ing during cutting, it must be locked

again by the lock lever (50).

Release lever for bevel tilt stop

The blade tilt setting has end stops at 0°

and 45°. For special bevel cuts (under-

cutting) the bevel angle can be in-

creased by 1.5° in both directions.

 Withdraw bevel angle limitation stop

(51) and place over the right-hand

cam plate = bevel angle of saw

blade adjustable between –1.5° and

45°.

 Withdraw bevel angle limitation stop

(51) and place over the left-hand

cam plate = bevel angle of saw

blade adjustable between 0° and

46.5°.

On/off switch

 To stop = press upper switch (52).

 To start = press and hold lower

switch (53) for 1 - 2 seconds.

6.4 Adjusting rip fence

For use as rip fence the long fence ex-

trusion (54) must be installed. It is

mounted on the guide extrusion at the

front of the saw table.

– Position rip fence to the right of the

saw blade.

The marking in the magnifying glass

shows the set distance between the

rip fence and the saw blade on the

scale.

– Release lock lever (55) of rip fence

and shift rip fence until marking in

magnifying glass indicates the de-

sired distance to the saw blade.

Press lock lever (55) downwards to

lock.

– For ripping, the fence extrusion (54)

must be parallel with the saw blade

and locked in position by the lock le-

ver (55). Press lock lever down-

wards to do this.

– Knurled nuts (56) for attaching the

fence extrusion. After loosening the

two knurled nuts (56), the fence ex-

trusion can be removed and shifted:

Small edge:

– for cutting thin stock;

– when the saw blade is tilted.

Wide edge:

– for cutting thick stock (max. 87

mm).

6.5 Adjusting pointer on rip

fence

1. Align rip fence with saw blade.

2. Loosen rip fence pointer fixing

screw.

3. Bring pointer on rip fence and "O" on

scale into alignment.

4. Retighten rip fence pointer fixing

screw.

Note:

To avoid stock jamming when cutting

along the rip fence:

slide rip fence all the way to the right ta-

ble edge and then back to the required

cutting width.

Note:

Adjust parallel stop (if necessary): To

prevent the workpiece from jamming be-

tween parallel stop and saw blade, the

parallel stop must be aligned to the saw

blade, or set to a max. of 0.3 mm open-

ing to the rear. To adjust it, release the 2

screws on the upper side of the parallel

stop and then tighten again.

Note:

Adjust clamping force of the parallel

guide (if required): If the rear clamp rear

clamping piece clamps earlier or later to

the front clamping piece, this can be ad-

justed by turning the nuts (on the rear).

Loosen the nut so that the rear clamping

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TS 254 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info