Bedienungsanleitung Metabo TS 254 (Seite 24 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

633940

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

ENGLISH

5. Cut workpiece by pushing the mitre

fence forward.

6. Switch machine off if no further cut-

ting is to be done immediately after-

wards.

Danger!

Before every transport:

 switch machine off.

 wait for saw blade to come to

standstill.

 unplug mains cable.

 Lower saw blade fully.

 Set saw blade bevel angle to 0° and

lock with lock lever.

 Remove add-on parts (blade guard,

dust extraction). Store blade guard

at saw table.

 Wind up mains cable on cable reel.

Only tools with machine stand:

 Raise tool on frame and swing to the

rear. Set up machine on its edge

and fold in upper legs. The red turn-

ing levers must engage again.

 Swing machine to the rear and fold

in the lower legs. The red turning le-

vers must engage again.

 Push in handles and set down ma-

chine.

Crushing hazard

Lock pulled-out table side extension

with lock lever.

Use handles (63) provided on sides of

table to carry the machine.

Caution!

Do not carry the machine at the

guards, table side extension or oper-

ating elements!

Mobile transport:

 Pull out handle, turn it and engage it.

 Pull or push saw with handle

If possible use original carton for ship-

ping.

Danger!

Prior to all servicing:

1. switch machine off.

2. wait until the saw has come to a

complete stop.

3. unplug mains cable.

– Check that all safety devices are op-

erational again after each service.

– Replace defective parts, especially

safety devices, only with genuine re-

placement parts. Parts not tested

and approved by the equipment

manufacturer can cause unforeseen

damage.

– Repair and maintenance work other

than described in this section should

only be carried out by qualified spe-

cialists.

Danger!

With a damaged table insert there is

a risk of small parts getting stuck

between table insert and saw blade,

blocking the saw blade. Replace

damaged table inserts immediately!

8.1 Saw blade change

Danger!

Directly after cutting the saw blade

can be very hot – burning hazard!

Let a hot saw blade cool down. Do

not clean the saw blade with com-

bustible liquids.

Risk of injury, even with the blade at

standstill. Wear gloves when chang-

ing blades.

When fitting a saw blade, observe

the direction of rotation!

1. Raise saw blade fully.

2. Remove blade guard.

3. Loosen table insert (64) and remove

from table.

4. Turn clamping nut (68) with open-

jawed spanner and , at the same

time, pull lever for saw blade lock

(65) upwards until it engages.

5. Hold lever firmly in position and un-

screw clamping nut clockwise.

6. Remove clamping nut (68), outer

blade flange (67) and saw blade

from saw spindle.

7. Clean clamping surfaces of saw

blade flange (66) and (67) and saw

blade.

7. Transport

8. Care And Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TS 254 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info