Bedienungsanleitung Metabo TS 254 (Seite 25 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

633940

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

ENGLISH

Danger!

Do not use cleaning agents (e.g. to

remove resin residue) that could

corrode the light metal components

of the saw; the stability of the saw

would be adversely affected.

8. Push inner saw blade flange (66)

onto motor shaft.

9. Put on a new saw blade (observe di-

rection of rotation!).

Danger!

Use only saw blades conforming to

the technical specifications stated

and to EN 847-1 – if unsuitable, dam-

aged or deformed saw blades parts

are used, parts can be ejected due

to centrifugal force in an explosive-

type manner.

Do not use:

– saw blades which permissible

maximum speed is below the rat-

ed no-load speed of the saw

spindle (see “Technical Specifi-

cations”);

– saw blades made of high speed

steel (HS or HSS);

– saw blades whose cutting width

is less than, or whose blade body

is thicker than, the thickness of

the riving knife.

– saw blades with visible damage;

– cut-off wheel blades.

Danger!

– Mount saw blade using only gen-

uine parts.

– Do not use loose-fitting reducing

rings; the saw blade could work

loose.

– Saw blades have to be mounted

in such way that they do not

wobble or run out of balance and

cannot work loose during opera-

tion.

10. Slide on outer blade flange (67).

11. Screw on clamping nut (68) (left-

handed thread!). Turn clamping nut

(68) with open-jawed spanner and,

at the same time, pull the lever of the

saw blade lock (65) upwards until is

engages.

12. Hold lever firmly in position and

tighten clamping nut hand-tight by

turning counterclockwise.

Danger!

– Do not extend arbor bolt tighten-

ing wrench.

– Do not tighten arbor bolt by hit-

ting the wrench.

13. Adjust riving knife corresponding to

the saw blade size (69).

(for riving knife setting, see 5.1)

14. Reinstall table insert.

15. Attach blade guard.

8.2 Adjusting the blade tilt

stop

1. Set the blade tilt stop lever (71) for

the angle range to 0° / 45°.

2. Lock set bevel tilt by tightening lock

lever (70).

3. Check blade bevel angle:

– 0° = at right angles to the saw ta-

ble

– 45° with separate mitre square.

If these angles are not achieved ex-

actly:

4. Release cross-head screw (72) at

respective cam disc and adjust cam

plate until the blade bevel angle in

relation to the saw table is exactly 0°

(= right angles), or 45°, in the end

positions.

5. Retighten cross-head screw at cam

plate.

6. After adjusting the stop limitation, re-

adjust angle scale at front side if

necessary.

Note:

To set the bevel angle limitation of -1.5°

to 46.5°, the blade tilt stop lever must be

pulled out.

8.3 Saw storage

Danger!

Store the machine beyond the reach

of children. Store the machine such

that it cannot be put into operation

by unauthorised personnel and such

that the stationary machine cannot

cause injury.

Caution!

Do not store saw unprotected out-

doors or in damp environment.

8.4 Maintenance

Saw Cleaning

 Remove chips and saw dust with

vacuum cleaner or brush:

– from saw blade setting guide ele-

ments;

– from motor vent slots;

–chip case.

–Height adjustment

– Swivel guide

Before switching ON

Visual check to see if

– distance between saw blade and riv-

ing knife is 3 to 5 mm.

– riving knife is in line with saw blade.

Visual check of power cable and power

cable plug for damage; if necessary

have damaged parts replaced by a

qualified electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TS 254 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info