Bedienungsanleitung Metabo WEPBA 17-125 Quick (Seite 18 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595532

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISHen

7.3 Securing/Releasing the "Quick"

clamping nut (depending on features)

Securing the "Quick" clamping nut (1):

Only attach the "Quick" clamping nut (1) to

tools with "Metabo Quick System". These

tools can be identified by the red spindle lock button

(4) with "M-Quick" logo

Do not use the "Quick" clamping nut if the

accessory has a clamping shank thicker than

6.8 mm! In this case, use the 2-hole nut (14) with 2-

hole spanner (15).

- Lock the spindle (see chapter 7.1).

- Position the "Quick" clamping nut (1) on the

spindle (2) so that the 2 lugs engage in the 2

grooves on the spindle. See illustration on page 2.

- Tighten the "Quick"clamping nut by turning

clockwise by hand.

- Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

Releasing the clamping nut (1):

Only when the "Quick" clamping nut (1) is

attached must the spindle be stopped using

the red M-Quick spindle locking button (4)!

- The machine continues to run after switching off.

- Press in the M-Quick spindle locking button (4)

just before the grinding disc stops. The "Quick"

clamping nut (1) loosens itself by around half a

turn and can be removed without additional effort

or tools.

7.4 Securing/Releasing the 2-hole nut

(depending on features)

Due to safety reasons, the nut with two holes

(14) must not be used for machines with the

designation W..B...

The 2 sides of the 2-hole nut are different. Screw the

2-hole nut onto the spindle as follows:

See illustration C on page 2.

- X) For thin grinding discs:

The edge of the 2-hole nut (14) faces upwards so

that the thin grinding disc can be attached

securely.

Y) For thick grinding discs:

The edge of the 2-hole nut (14) faces downwards

so that the 2-hole nut can be attached securely to

the spindle.

- Locking the spindle. Turn the 2-hole nut (14)

clockwise using the 2-hole spanner (15) to secure.

Releasing the 2-hole nut:

- Lock the spindle (see chapter 7.1). Turn the 2-hole

nut (14) anticlockwise using the 2-hole spanner

(15) to unscrew.

8.1 Adjusting the speed (depending on

features)

Set the recommended speed at the thumbwheel

(8). (small number = low speed; large number =

high speed)

Cutting disc, roughing disc, cup wheel and diamond

cutting disc: high speed

Brush: medium speed

Sanding plate: low to medium speed

Note:

We recommend using our angle polisher for

polishing work.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

WA..., WBA..., WEA..., WEVA..., WEBA...: In

continuous operation, the machine continues

running if it is forced out of your hands. Therefore,

always hold the machine with both hands using the

handles provided, stand securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

Machines with slide switch:

Switching on: Push the slide switch (5) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (5) and release it.

Machines with paddle switch

(with dead man function):

Switching on: : Slide paddle switch (10) in the

direction of the arrow and then press the

paddle switch (10).

Switching off: Release the paddle switch (10).

8.3 Working Directions

Grinding and sanding operations:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

8. Use

1010

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPBA 17-125 Quick Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info