Bedienungsanleitung Metabo WEPBA 17-125 Quick (Seite 19 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595532

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH en

Rough grinding: position the machine at an angle of

30° - 40° for the best working results.

Cutting-off operations:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Wire brushing:

Press down the machine evenly.

8.4 Rotate gear housing

See illustration E on page 3.

- Disconnect from the power supply.

- Unscrew the fastening screw (a) of the lever (16).

Remove the screw, lever (with its sheet metal part)

and put aside.

- Unscrew the 4 gear housing screws (b).

CAUTION! Do not remove the gear housing!

- Turn the gear housing to the desired position

without removing it.

- Screw in the 4 gear housing screws (b) in the

available threads! Tightening torque = 3.0 Nm +/-

0.3 Nm.

- Slide the spring that pushes the lever in position to

the side and re-insert the lever (16) (with its sheet

metal part), and fix with the fastening screw (a).

Tightening torque = 5.0 Nm +/- 0.5 Nm. Check the

lever for correct function: it has to be under spring

tension.

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of

the power tool. Conductive build-up can impair the

protective insulation of the power tool and cause

electrical hazards.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

Machines with VTC, TC and VC electronics:

The electronic signal display (7) lights up

and the load speed decreases. There is too

much load on the machine! Run the machine

in idling until the electronics signal indicator

switches off.

Machines with VTC, TC and VC electronics:

The electronic signal display (7) flashes

and the machine does not start. The restart

protection is active. If the mains plug is

inserted with the machine switched on, or if the

power supply is restored following an interruption,

the machine does not start up. Switch the machine

off and on again.

Use only genuine Metabo accessories.

See page 5.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

A Cutting guard clip / guard for cut-off

grinding

Designed for work with cutting disc and diamond

cutting discs. Once the cutting guard clip is fitted,

the safety guard becomes a cutting guard.

B Extraction guard for cut-off grinding

Designed for cutting through stone slabs with

diamond cutting discs. With nozzle for extracting

stone dust using a suitable extraction unit.

C Extraction guard for surface grinding

Intended for grinding of concrete, screed, wood and

plastics with diamond cup wheels and/or fibre discs

and suitable sanding plates. With nozzle for

extracting stone, wood and plastic dust using a

suitable extraction unit. Not suitable for extracting

sparks or for grinding of metals.

D Dust filter

The fine mesh filter prevents coarse particles from

entering the motor housing. Remove regularly and

clean.

E Hand protection

Intended for work with backing pads, sanding

plates, wire brushes and support plates, sanding

pads, wire brushes and diamond Drill Bits for tiles.

Install hand guard under the additional side-

mounted handle.

F Multiple position bar for side handle

Permits numerous handle positions.

For a complete range of accessories, see

www.metabo.com or the accessories catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If the connection lead is damaged, it must be

replaced by a special connection lead.

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

The generated grinding dust may contain harmful

substances. Dispose appropriately.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Directive 2002/

9. Cleaning

10. Troubleshooting

11. Accessories

12. Repairs

13. Environmental Protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPBA 17-125 Quick Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info