Bedienungsanleitung Metabo WEPF 15-150 Quick (Seite 16 von 112) (Alle Sprachen)

625647

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISHen

- Ensure good ventilation of the workplace and

keep it clean using a vacuum cleaner. Sweeping

or blowing stirs up dust.

- Vacuum or wash protective clothing. Do not blow,

beat or brush.

See page 2.

1 Clip to tighten/release the (tool-free) clamping

nut manually *

2 Clamping nut (tool-free) *

3 Support flange

4Spindle

5 Spindle locking button

6Safety cover

7 Side handle/Additional handle with vibration

damping *

8 Sliding on/off switch *

9Handle

10 Electronic signal indicator

11 Speed adjustment wheel *

12 Switch-on lock*

13 Trigger switch *

14 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

type plate match your power supply.

Always install an RCD with a maximum trip

current of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle (7)

attached! Attach the additional handle on the

left or right of the machine and secure.

6.2 Attach the safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter 11. Accessories!

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cutting discs.

See illustration C on page 2.

- Place the safety guard (6) in the position

indicated.

- Push the lever (14) and turn the safety guard until

the closed section is facing the operator.

- Release lever and rotate guard

until the lever latches.

- Make sure that the guard is placed securely: The

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least 3.4

mm by the safety guard.

(Disassemble in reverse

order.)

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the cut-off

grinding guard before performing cut-off

grinding work (see Chapter 11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (5) only

when the spindle is stationary.

- Press in the spindle locking button (5) and

turn the spindle (4) by hand until the spindle

locking button engages.

7.2 Placing the grinding wheel in position

See illustration B on page 2.

- Fit the support flange (3) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Place the grinding wheel on the support flange (3).

The grinding wheel must lay flat on the supporting

flange.

7.3 Securing/releasing the (tool-free)

clamping nut

Only tighten the (tool-free) clamping nut (2) by

hand!

For the machine to operate, the clip (1) must

always lie flat on the clamping nut (2).

To secure the (tool-free) clamping nut (2):

Use only accessories which fulfil the

specifications. See Chapter 14. Technical

Data).

- Lock the spindle (see chapter 7.1).

- Flip up the clip (1) on the clamping nut.

- Fit the clamping nut (2) on the spindle (4). See

illustration A on page 2.

- Tighten the clamping nut on the clip (1) manually

in a clockwise direction.

- Flip down the clip (1) again .

Release the (tool-free) clamping nut (2):

- Lock the spindle (see chapter 7.1).

- Flip up the clip (1) on the clamping nut.

- Unscrew the clamping nut (2), turning it

anticlockwise manually .

Note:

If the clamping nut (2) is very tightly secured,

you can also use a 2-hole spanner to unscrew it.

8.1 Adjusting the speed (depending on

features)

Set the recommended speed at the thumbwheel

(11). (small number = low speed; large number =

high speed)

Cutting disc, roughing disc, cup wheel and diamond

cutting disc: high speed

Brush: medium speed

Sanding plate: low to medium speed

5. Overview

6. Commissioning

7. Attaching the grinding wheel

8. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPF 15-150 Quick Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info