Bedienungsanleitung Metabo WEPF 15-150 Quick (Seite 17 von 112) (Alle Sprachen)

625647

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH en

Note: We recommend using our angle polisher for

polishing work.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Machines with slide switch:

Switching on: Push the sliding switch (8) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the sliding

switch (8) and release the sliding switch.

WEPF 15-150 Quick:

"Paddle switch" (with dead man's function):

Switching on: Slide the switch-on lock (12) in the

direction of the arrow and press the trigger

switch (13).

Switching off: Release the trigger switch (13).

WEPBF 15-150 Quick:

"Paddle switch" (with dead man's function):

Switching on: Slide the trigger switch (13) in the

direction of the arrow and press the trigger

switch (13).

Switching off: Release the trigger switch (13).

8.3 Working Directions

Grinding and sanding operations:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Rough grinding: position the machine at an angle of

30° - 40° for the best working results.

Cut-off grinding:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Wire brushing:

Press down the machine evenly.

8.4 Rotate gear housing

See illustration D on page 3.

- Disconnect the mains plug.

- Remove guard (6).

- Unscrew the 4 gear housing screws (a).

CAUTION! Do not remove the gear housing!

- Turn the gear housing to the desired position

without removing it.

- Screw in the 4 gear housing screws (a) in the

available threads! Tightening torque = 3,0 Nm +/-

0,3 Nm.

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of the

power tool. Conductive build-up can impair the

protective insulation of the power tool and cause

electrical hazards.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

Regularly clean dust filter: remove and blow out

with compressed air.

- Electronic safety shutdown The electronic

signal display (10) flashes and the machine

was automatically SWITCHED OFF. If the slew

rate of the current is too high (for example, if the

machine suddenly seizes or kickback occurs), the

machine switches off. Switch machine off with

switch. Switch it on again and continue to work as

normal. Try to prevent the machine from seizing.

See chapter 4.2.

Machines with VTC and TC electronics:

The electronic signal display (10) lights

up and the load speed decreases. There is

too much load on the machine! Run the

machine in idling until the electronics signal

indicator switches off.

Machines with VTC, TC and VC electronics:

The electronic signal display (10) flashes

and the machine does not start. The restart

protection is active. If the mains plug is

121212 131313

1010

9. Cleaning

10. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPF 15-150 Quick Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info