Bedienungsanleitung Metz MECABLITZ 48 AF-1 digital Nikon (Seite 74 von 139) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

517332

Zoom out

Zoom in

Vorherige Seite

1/139

Nächste Seite

then the display of the flash unit will briefly indicate the underexposure in f-stops

ranging from -0.3 EV to -3.0 EV in one-third increments. In borderline instances

the flash unit will not display an „OK“, or the flash symbol will blink in the

camera viewfinder, even though the exposure is correct. In this instance, no indi-

cation will appear!

To enable underexposure warnings, the TTL mode (for example. ,

, BL must be set!

6 Displays in the camera viewfinder

Examples of displays in the camera viewfinder:

A green arrow symbol lights up:

Command to switch on or use the flash unit.

A red arrow symbol

lights up:

The flash unit is ready for firing.

A red arrow symbol remains lit up after the shot or goes out briefly:

The exposure was correct.

A red arrow symbol

blinks after shooting:

The shot was underexposed.

For information applicable to the displays in the viewfinder of your

camera model, refer to the camera’s operating instructions.

☞

TTLTTL

TTL

☞

7 Flash modes („Mode“)

Depending on the camera model or camera group (see Table 1), various TTL

flash modes and the manual flash mode are available. To set the flash mode, a

data exchange must therefore occur before the flash unit and camera, e.g. by

tapping the camera’s shutter release. Setting of the flash mode occurs with the

„Mode“ ባ button.

7.1 TTL-flash modes

The TTL flash modes offer a very simple method of achieving very good flash

shots. In these modes, exposure readings are taken by a sensor built into the

camera, which measures the amount of light through the camera lens (TTL =

„Through The Lens“). Here the camera automatically determines the flash perfor-

mance required for a correct exposure of the shot. The advantage of the TTL flash

modes is that all factors influencing exposure (filters, change of aperture and

focal length with zoom objectives, extensions for close-ups, etc.) are automatical-

ly taken into account in adjusting the flash light. The symbol appears depen-

ding on the camera model and means that preflash measuring technology is in

operation, for example, in i-TTL, D-TTL and 3D. The symbol „BL“ (BL = balanced

light) indicates that the distance data of the lens (for example, 3D function) were

taken into account in the flash exposure and/or that a fill-in flash is involved.

If the shot was correctly lit, the correct exposure indication ብ will flash „OK“ for

about 5 seconds (see 4.2).

Please note whether there are limitations for your camera in terms of

film sensitivity for TTL flash mode (for example, ISO 64 to ISO 1000; see

camera’s operating instructions)! In analogue cameras there must be a

film in the camera to test the TTL function!

i-TTL and D-TTL flash mode

The i-TTL flash mode is supported by cameras of Group E, the D-TTL flash mode

by cameras of Group D (see Table 1). i-TTL and D-TTL flash modes are advan-

ced variants of the normal TTL flash modes used with analogue cameras. Before

☞

707 47 0081.A2 48AF-1Nikon/Inh. 19.09.2007 12:42 Uhr Seite 74

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 48 AF-1 digital Nikon Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info