Bedienungsanleitung Metz MECABLITZ 50 AF-1 digital Pentax (Seite 96 von 182) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

517341

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

8 Manual flash exposure correction

The auto flash exposure mode of most cameras is adjusted to a reflection factor

of 25% (the average reflection factor of flash subjects). A dark background that

absorbs much of the light or a highly reflective bright background (backlit shots,

for example) may result in, respectively, underexposure or overexposure of the

subject.

To offset these effects, the flash exposure can be adjusted manually for the shot

with a correction value. The extent of the correction depends on the contrast bet-

ween the subject and background!

In P-TTL flash modes (P-TTL, P-TTL-HSS) , manual flash exposure correction

factors of from -3 EV (f-stops) to +3 EV (f-stops) can be adjusted on the flash

unit in one-third increments.

Tip:

Dark subject against light background: positive correction factor. Light subject

against dark background: negative correction factor.

Exposure correction by means of alteration of the lens aperture setting is

impossible, since the camera’s automatic exposure program regards the

altered aperture setting as the normal working aperture setting.

When setting the correction factor, the distance shown in the display can

change and be adjusted to the correction factor (depending on the

camera model)!

Setting procedure

• Press button — or + until „EV“ flashes.

Set a negative correction factor with the

button — or a positive one with the

button +.

The setting takes effect immediately.

☞

After about 5 seconds the display stops flashing and the setting is saved auto-

matically. After saving, „EV“ appears in the display with the correction value.

Press the button — or + until „EV“ without a

correction factor is shown. The setting takes

effect immediately.

After about 5 seconds the display stops flashing and

the setting is saved automatically.

Manual flash exposure correction is only possible in TTL flash mode if the

camera supports this function (consult the camera’s operating instruc-

tions)! If the camera does not support this function, the adjusted correc-

tion will have no effect. If the camera does not support this function, no

corrective value can be set on the flash unit, the corrective value remains

ineffective.

For some camera models, the manual flash exposure corrections must be adju-

sted on the camera. If this is the case, no correction value will appear on the

flash unit display.

After the shot, remember to cancel the flash exposure correction!

Attention: Strongly reflecting objects in the motif can have a negative impact

on the camera’s automatic exposure. The photograph will be

underexposed. Remove reflecting objects or set a positive

correction value.

☞

0,7

Zoom

TTLP

☛

0,7

Zoom

TTLP

☛

709 47 0191.A3 50AF-1 Pen. 17.12.2010 13:22 Uhr Seite 96

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 50 AF-1 digital Pentax Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info