Bedienungsanleitung Metz MECABLITZ 50 AF-1 digital Pentax (Seite 97 von 182) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

517341

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

9 Special functions („Select“)

Depending on the camera model, various special functions are available.

For this purpose, data exchange must first occur between the flash unit and

camera to access and set the special functions, for example by tapping the

shutter release.

Accessing the individual special functions is achieved

with the button „Select“, that is to say, the buttons —

or + must be pressed simultaneously.

The accompanying special functions and settings des-

ired are then carried out individually with the

button — or +.

The setting must occur immediately after accessing the special functions

since otherwise the flash unit automatically switches back to normal

flash operation after a few seconds!

9.1 Motor zoom main reflector („Zoom“)

The motor zoom main reflector ቫ of the flash unit can illuminate lens angles

from 24 mm (35 mm format): Thanks to the use of the integrated wide-angle

diffuser ቩ, the illumination widens to 12 mm.

Auto zoom

The zoom position of the main reflector

ቫ

is automatically adjusted to the lens

focal length when the flash unit is used with a camera that transmits the data rela-

ted to the lens focal length. After the flash unit has been switched on, „Zoom“ and

the current zoom position of the main reflector

ቫ

are shown in the display.

Automatic adjustment occurs for lens focal lengths from 24 mm. If a focal length

of less than 24 mm is used, „24“ flashes in the display as a warning that the

shot cannot be completely lit.

☞

The automatic adjustment will not be activated if the main reflector is

swivelled, if the wide-angle diffuser ቩ is pulled out, or a Mecabounce

(accessory) is mounted.

If so desired, the position of the main reflector ቫ can be manually adjusted in

order to achieve particular lighting effects (such as spot effect etc.).

Manual zoom mode

For cameras that do not transfer any data regarding the focal length (e.g. when

using a manual focus lens), the zoom position of the main reflector must be

adjusted to the lens focal length. In this case auto-zoom mode is not possible!

After switching on the flash unit, „Zoom“ appears in the display and the current

zoom position of the main reflector ቫ appears.

Setting procedure

• Press button combination „Select“ until „Zoom“

appears flashing next to the zoom position (mm).

• Apply the setting desired with the buttons + and —.

The flashing display changes to „M.Zoom“ for

manual zoom mode.

The following zoom positions are possible

for the main reflector:

24 - 28 - 35 - 50 - 70 - 85 - 105 mm

(35 mm format).

The setting takes effect immediately.

After about 5 seconds the display stops flashing and

the setting is saved automatically.

When the camera transmits the lens focal length to the flash unit and a

☞

☛

M Zoom

☛

709 47 0191.A3 50AF-1 Pen. 17.12.2010 13:22 Uhr Seite 97

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 50 AF-1 digital Pentax Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info