Bedienungsanleitung Metz MECABLITZ 54 AF-1 Minolta (Seite 58 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

517350

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

4.4 Manual flash mode

Various cameras automatically switch the flash unit to TTL flash mode when

in Program “P” or in one of the Subject Program Modes. Manual flash ope-

ration is then no longer possible. There is no correct exposure confirmation

given on the LC display of the flash unit in the manual flash mode!

Set „Av“ aperture priority or the „M“ or „X“ manual modes on the camera.

Select the aperture and shutter speed (with „M“) on the camera according to

the given photographic situation (see the camera’s operating instructions).

4.4.1 Manual flash mode M with full light output

In this mode the flash unit always fires uncontrolled flashes at full light output.

Adaptation to the given photographic situation is only by adjusting the aper-

ture setting on the camera accordingly. The LC display of the flash unit will

indicate the flash-to-subject distance that has to be maintained for a correct

exposure (see also 5.4.2).

Setting procedure for the manual flash mode M

• Turn on the flash unit by its main switch.

• Continue depressing the „Mode“ key until „M“ flashes on the LC display.

• The setting becomes immediately effective. The LC display is returned to its

normal state after approx. 5 sec.

4.4.2 Manual flash mode MLo with partial light output levels

In this mode the flash unit always fires an uncontrolled flash at a manually set

partial light output level (Low). Adaptation to the prevailing photographic si-

tuation is by selecting an appropriate partial output level or by setting a cor-

responding aperture on the camera. The LC display panel of the flash unit

will indicate the distance required for correct flash exposure (also see 5.4.2).

Setting procedure for the manual flash mode MLo:

• Turn on the flash unit with the main switch.

• Continue depressing the “Mode” key until “M” flashes on the LC display.

• Continue depressing the “Select” key combination (= “Mode” key +

“Zoom” key) until P appears on the LC display.

☞

• Alongside P, the set partial light output value flashes.

• The partial light output level can be diminished with the “Mode” key, or

increased with the “Zoom” key, while the manual partial light output value

is flashing. In this manner, you can set partial light output values of P 1/8 ,

P 1/4, P 1/2 and P 1/1 (maximum output).

• The setting immediately becomes effective. After approx. 5 sec. the LC dis-

play returns to its normal state. When the partial light output level has been

set , MLo is displayed on the LC panel but the set light output value is not

indicated. The indicated distance is adapted to the partial light output level.

Depress the “Select” key combination (= “Mode” key + “Zoom” key) to dis-

play the partial light output value.

Changing the flash mode, e.g. to TTL, resets the manual light output

level to P 1/1 (maximum light output).

4.5 Flash techniques

4.5.1 Bounce flash

Photos shot with full frontal flash are easily recognized by their harsh, dense

shadows. This is often associated with a sharp drop in light from the fore-

ground to the background. This phenomenon can be avoided with bounce

flash because the diffused light will produce a soft and uniform rendition of

both the subject and the background. For this situation the reflector is turned

in such a manner that the flash is bounced off a suitable reflective surface

(e.g. ceiling or wall of the room).

The reflector can be turned verticall up to 90°. When turning the reflector

vertically, it is essential to ensure that it is moved by a sufficiently wide angle

so that direct light can no longer fall on the subject. Consequently, always

turn the reflector at least to the 60° lock-in position. The distance readings on

the LC display will disappear. The flash-to-subject distance via the ceiling or

wall is an unknown magnitude.

☞

54 AF-1 M 03.08.2004 10:53 Uhr Seite 58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 54 AF-1 Minolta Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info