Bedienungsanleitung Microlife BP 3AG1-30 en W (Seite 6 von 43) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch)

536814

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Memory full

Pay attention that the maximum memory capacity of 30 is

not exceeded. When the memory is full, the old values

are automatically overwritten with new ones. Values

should be evaluated by a doctor before the memory

capacity is reached – otherwise data will be lost.

Clearing all values

If you are sure that you want to permanently remove all stored

values, hold down the M-button (the device must have been

switched off beforehand) until «CL» appears and then release the

button. To permanently clear the memory, press the M-button

while «CL» is flashing. Individual values cannot be cleared.

How not to store a reading

As soon as the reading is displayed press and hold the ON/OFF

button 1 until «M» AO is flashing. Confirm to delete the reading by

pressing the M-button 8.

6. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol

will flash as soon as the device is switched on (partly filled battery

displayed). Although the device will continue to measure reliably, you

should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol AN will flash as soon

as the device is switched on (flat battery displayed). You cannot

take any further measurements and must replace the batteries.

1. Open the battery compartment 5 at the back of the device.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

Which batteries and which procedure?



Use 4 new, long-life 1.5 V, size AA batteries.



Do not use batteries beyond their date of expiry.



Remove batteries if the device is not going to be used for a

prolonged period.

Using rechargeable batteries

You can also operate this device using rechargeable batteries.



Only use «NiMH» type reusable batteries.



Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

device as they may become damaged (total discharge as a

result of low use of the device, even when switched off).



Always remove the rechargeable batteries if you do not

intend to use the device for a week or more.



Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

7. Using a Mains Adapter

You can operate this device using the Microlife mains adapter (DC

6V, 600mA).



Only use the Microlife mains adapter available as an orig-

inal accessory appropriate for your supply voltage.



Ensure that neither the mains adapter nor the cable are

damaged.

1. Plug the adapter cable into the mains adapter socket 4 in the

blood pressure monitor.

2. Plug the adapter plug into the wall socket.

When the mains adapter is connected, no battery current is consumed.

8. Error Messages

If an error occurs during the measurement, the measurement is

interrupted and an error message, e.g. «ERR 3», is displayed.

Error

Description

Potential cause and remedy

ERR 1

» Signal too

weak

The pulse signals on the cuff are too weak.

Re-position the cuff and repeat the

measurement.*

ERR 2

» Error signal During the measurement, error signals were

detected by the cuff, caused for instance by

movement or muscle tension. Repeat the

measurement, keeping your arm still.

ERR 3

» No pressure

in the cuff

An adequate pressure cannot be generated

in the cuff. A leak may have occurred.

Check that the cuff is correctly connected

and is not too loose. Replace the batteries if

necessary. Repeat the measurement.

ERR 5

» Abnormal

result

The measuring signals are inaccurate and

no result can therefore be displayed. Read

through the checklist for performing reliable

measurements and then repeat the

measurement.*

» Pulse or

cuff pres-

sure too

high

The pressure in the cuff is too high (over

300 mmHg) OR the pulse is too high (over

200 beats per minute). Relax for 5 minutes

and repeat the measurement.*

» Pulse too

low

The pulse is too low (less than 40 beats per

minute). Repeat the measurement.*

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife BP 3AG1-30 en W Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info