Bedienungsanleitung Microlife BP A7 Touch BT (Seite 6 von 101) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

773522

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite



Do not remove the cuff between measurements.



If one of the individual measurements was questionable, a fourth

one is automatically taken.

AF detection is only activated in AFIB/MAM mode.

3. Checklist for Taking a Reliable Measurement



Avoid activity, eating or smoking immediately before the

measurement.



Sit down on a back-supported chair and relax for 5 minutes.

Keep the feet flat on the floor and do not cross your legs.



Always measure on the same arm (normally left). It is recom-

mended that doctors perform double arm measurements on a

patients first visit in order to determine which arm to measure in

the future. The arm with the higher blood pressure should be

measured.



Remove close-fitting garments from the upper arm. To avoid

constriction, shirt sleeves should not be rolled up - they do not

interfere with the cuff if they are laid flat.



Always ensure that the correct cuff size is used (marking on the

cuff).

Fit the cuff closely, but not too tight.



Make sure that the cuff is positioned 1-2 cm above the elbow.

The artery mark on the cuff (ca. 3 cm long bar) must lie over

the artery which runs down the inner side of the arm.

Support your arm so it is relaxed.

Ensure that the cuff is at the same height as your heart.

4. Taking a Blood Pressure Measurement

1. Slide the lock switch 3 down to the «unlock» position.

2. Select standard (single measurement) or AFIB/MAM mode

(automatic triple measurement): see details in chapter «2.».

3. Press the START/STOP button AN to start the measurement.

4. The cuff will now pump up automatically. Relax, do not move

and do not tense your arm muscles until the measurement

result is displayed. Breathe normally and do not talk.

5. When the correct pressure is reached, the pumping stops and the

pressure falls gradually. If the required pressure was not reached,

the device will automatically pump some more air into the cuff.

6. During the measurement, the pulse indicator BR flashes in the

display.

7. The result, comprising the systolic AP and the diastolic AQ blood

pressure and the pulse rate AR is displayed. Note also the

explanations on further display symbols in this booklet.

8. When the device has finished measuring, remove the cuff.

9. Switch off the device. (The monitor does switch off automatically

after approx. 1 min.).

AF detection is only activated in AFIB/MAM mode.

You can stop the measurement at any time by pressing the

START/STOP button (e.g. if you feel uneasy or an

unpleasant pressure sensation).

This monitor is specially tested for use in pregnancy and

pre-eclampsia. When you detect unusual high readings in

pregnancy, you should measure after a short while again

(eg. 1 hour). If the reading is still too high, consult your

doctor or gynecologist.

In pregnancy the AFIB symbol can be ignored.

How not to store a reading

As soon as the reading is displayed press and hold the START/

STOP button AN until «M» AO is flashing. Confirm to delete the

reading by pressing the M-button AO.

«CL» is displayed when the reading is deleted from the

memory successfully.

How do I evaluate my blood pressure?

The LED traffic light indicator on the left-hand side of the display

indicates within which range the measured blood pressure lies. The

value is either within the optimum (green), elevated (yellow) or high

(red) range. The classification corresponds to the following ranges

defined by international guidelines (

ESH, ESC, JSH

). Data in mmHg.

The higher value is the one that determines the evaluation.

Example: a blood pressure value of 140/80 mmHg or a value of

130/90 mmHg indicates «blood pressure too high».

Range Systolic Diastolic Recommendation

1. blood pressure

too high

≥135 ≥85 Seek medical

advice

2. blood pressure

elevated

130 - 134 80 - 84 Self-check

3. blood pressure

normal

<130 <80 Self-check

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife BP A7 Touch BT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info