Bedienungsanleitung Midas XL48 (Seite 16 von 32) (Englisch)

658472

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

XL48 Microphone Pre-amplier

2. Getting Started

This section shows you how to unpack, install, connect up, power up and

congure the XL48 unit.

◊ This equipment is supplied by a mains voltage that can cause electric

shock injury.

◊ Before installing, setting up or operating this equipment, make sure

that you have read and fully understand all of this section and the

“Important safety instructions” at the front of this manual.

2.1 Unpacking

Carefully unpack your XL48 equipment package.

Then, inspect the XL48 unit carefully for any signs of damage that may have

occurred during transit and notify the courier immediately if you discover any.

Check the contents of your XL48 equipment package. If there are any parts

missing, incorrect or faulty, please contact your local distributor or Midas at the

address at the front of this manual.

Please retain the original packing in case you should need to return the

equipment to the manufacturer or supplier, or transport or ship the unit later.

2.2 Installation

Before installing and operating this equipment, make sure it is correctly

connected to the protective earth conductor of the mains voltage supply socket

outlet through the mains lead.

Ideally a cool area is preferred, away from power distribution equipment or other

potential sources of interference.

Do not install the equipment in places of poor ventilation.

Do not install this equipment in a location subjected to excessive heat,

dustormechanical vibration. Allow for adequate ventilation around

the equipment, making sure that its fans and vents are not obstructed.

Wheneverpossible, keepthe equipment out of direct sunlight.

Mount in rack only.

Power

◊ The supply cord must be unplugged to ensure complete

de-energisation of the unit.

The internal power supply is of the switch mode type that automatically senses

the incoming mains voltage and will work where the nominal voltage is in the

range 100VAC to 240VAC.

A mains inlet is provided on the rear panel. The correct lead for connection in

the area to which the unit was shipped is supplied with the unit. The equipment

should only be plugged into the mains outlet using the supplied lead.

Handling the equipment

When lifting or moving the equipment, always take its size and weight into

consideration.

Completely isolate the equipment electrically and disconnect all cables from the

equipment before moving it.

Do not insert your ngers or hands in any gaps or openings on the equipment,

forexample, vents.

Electric elds

In accordance with Part 15 of the FCC Rules & Regulations, “… changes or

modications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.”

Should this product be used in an electromagnetic eld that is amplitude

modulated by an audio frequency signal (20 Hz to 20 kHz), the signal to

noise ratio may be degraded. Degradation of up to 60dB at a frequency

correspondingto the modulation signal may be experienced under extreme

conditions (3V/m,90% modulation).

2.3 Connecting up

Connect up the rear panel of your unit as required:

• Inputs:

• XLR mic/line inputs (up to eight).

• Parallel analogue inputs (eight).

• External word clock.

• Outputs:

• AES3 outputs. There are two sets of eight AES3 mono output channels

(1 to 8), one set are on connectors 1 to 4 and the other set are on

connectors 5 to 8.

• Analogue outputs (eight).

• ADAT outputs (optional) — for connecting, for example, a sound

card (for PC) or an ADAT recorder. At 44.1kHz and 48kHz sample

frequencies the two ADAT ports are identical and both provide eight

output channels (1 to 8). At 88.2kHz and 96kHz sample frequencies,

bothportsprovidefour output channels each (port 1 = channels 1 to 4

and port2= channels 5 to 8).

• Internal word clock.

• Mains power — connect the IEC connector of the mains cable into the rear

of the unit and then plug it into a mains power outlet.

2.4 Powering the unit on/o

As the XL48 has no power on/o switch the unit is powered on/o via the

mainsoutlet.

2.5 Conguration

After you have powered up the XL48 you can congure the clock source and

sample rate as required.

midasconsoles.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas XL48 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info