Bedienungsanleitung Midea MUED-Serie (Seite 13 von 25) (Englisch)

588088

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

installation manual

CAUTION

The drain pipe of indoor unit must be heat insulated, or it will

condense dew, as well as the connections of the indoor unit.

Hard PVC binder must be used for pipe connection, and make

sure there is no leakage.

Drainage test

Install the drain joint of the outdoor unit

Check whether the drainpipe is unhindered.

New built house should have this test done before

paving the ceiling.

With the connection part to the indoor unit, please be noted not

to impose pressure on the side of indoor unit pipes.

When the declivity of the drain pipe downwards is over 1/100,

there should not be any winding.

The total length of the drain pipe when pulled out traversely

shall not exceed 20m, when the pipe is over long, a prop stand

must be installed to prevent winding.

Refer to the Fig.8-1 for the installation of the pipes.

All the figures in this manual are for explanation purpose only.

They may be slightly different from the air conditioner you

purchased.The actual unit shall prevail.

1.5m~2m

Insulating

material

Downward declivity

lower than 1/100

Bend

S shape

VP30

Downward declivity

lower than 1/100

Put as deep as possible

(about 10cm)

Fig. 8-1

Seal

The base pan hole

of outdoor unit

Drain joint

Seal

The base pan

of outdoor unit

Drain

joint

Fig.8-2

NOTE

Outdoor unit is equiped with a drain piping. Its position is

shown figure below

Drain Piping

Fig.8-2

Fit the seal into the drain joint, then insert the drain joint into

the base pan hole of outdoor, rotate 90

to securely

assemble them. Connect the drain joint with an extension

drain hose (Locally purchased), in case of the condensate

draining off the outdoor unit during the heating mode.(Refer

to Fig.8-2)

Plug

Slope 2%

Prepare a polyviny chloride with 21mm inner diameter

Connect a siphon, as shown in figure below

Fasten the tube to the drain hose with an adhesive and the

field-supplied clamp. The drain piping must be performed with

a DOWN-SLOPE pitch of 1/25 to 1/100

A B

18～24 595 1200

36 624 1381

48～60 646 1385

MODEL

Table 8-1

Fig.8-3

9. WIRING

The appliance shall be installed in accordance with

national wiring regulations.

The air conditioner should use separate power supply

with rated voltage.

The external power supply to the air conditioner should

have ground wiring, which is linked to the ground wiring

of the indoor and outdoor unit.

The wiring work should be done by qualified persons

according to circuit drawing.

unit：mm

An all-pole disconnection device which has at least 3mm

sepaaration distance in all pole and a residual current

device (RCD) with the rating of above 10mA shall be

incorporated in the fixed wiring according to the national

rule.

Be sure to locate the power wiring and the signal wring

well to avoid cross-disturbance.

Do not turn on the power until you have checked

carefully after wiring.

The power cord type designation is H07RN-F.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MUED-Serie Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MUED-Serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info