Bedienungsanleitung Midland Alan HP450 2A Rugged (Seite 13 von 26) (Englisch)

622039

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

channels hold down p or q.

3) Press PTT(orwaitveseconds)tostorethesetting.

2It is obvious that other parties shall also have to select the same

channel, otherwise communications will not be possible.

2This adjustment must be carried out within ve seconds, otherwise

the radio returns to the standby mode storing the currently set

channel.

5.5.a How to select the channel

The HP450 2A radio has been programmed as follows:

• Channelsfrom1 to 8 are programmed with the 8 radio frequencies

of the PMR446 band

• Channels from 9 onwards are programmed with the same

repeated radio frequencies (for example channel 9 has the same

frequency of channel 1, channel 10 has the same frequency of

channel 2, etc.), but also include CTCSS tones or DCS codes. If

you select these channels, CTC or DCS displays.

2For the PMR band, your dealer will inform you about the channels

to use

I If you need to communicate with transceivers of different

brands, it is generally preferable to use one of the rst eight

channels to ensure maximum compatibility. It is obviously

necessary to select the less used channel of your area. If the

parties you are communicating with use a HP450 2A device

(or a device with CTCSS tones), you may choose any channel.

If all the eight PMR446 frequencies are occupied in your area,

you can select a channel from 9 to 16 (the less busy one) to

allow the CTCSS tone or DCS code to enable you to listen to

communications of the members of your group only.

2For more information on CTCSS tones and DCS codes, see O 5.8

and 5.9.

5.6 Receiving and transmitting

2The reception/transmission mode described below is the so-called

"open trafc mode", which is simplest one. It is however possible

also to set other modes as described in paragraph 5.8.

During reception and transmission try and keep the aerial as vertical

as possible so that the signal can be transmitted without hindrances.

This precaution optimises the radio signal.

5.6.a Reception

As soon as the signal has been received, the squelch disables

automatically, the status LED turns green and icon

displays

showing the intensity of the received signal.

2If the signal is received fragmented because of weak signals, try

using the monitoring feature.

5.6.b Transmission

1) Verify that other parties are not connected to the selected channel

(status LED off).

2) Hold PTT down: the status LED turns permanently red to indicate

that the transmission is in progress, while indicator

indicates

the transmission power.

3) Waitafewseconds,thentalknormallyataboutvecentimetresfrom

the transceiver transmitter. Your message will be simultaneously

heard by all the parties listening to the same channel.

4) To end the communication, press PTT: the status LED switches

off to indicate that the device has returned to the reception mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland Alan HP450 2A Rugged Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland Alan HP450 2A Rugged

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info