Bedienungsanleitung Midland Alan HP450 2A Rugged (Seite 15 von 26) (Englisch)

622039

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

call. To communicate in condential mode, enable the scrambler

O 6.5.

2If you need to use the HP450 2A radio next to electric equipment

that generates impulses that frequently enable the squelch of

the radio (that is the radio cannot be permanently silenced when

there are signals and noise can be occasionally perceived), it is

generally preferable to use the restricted trafc mode.

5.9 Programming the CTCSS/DCS codes

It is possible to change the CTCSS tones or DCS codes on all the

channels. You can set different codes in TX and RX.

5.9.a Selecting the CTCSS tones

1) Select the operating channel.

2) Press MENU twice. CTC displays on the left along with the

ashingvaluethathasbeensetontheright:oF (disabled) or a

number ranging from 1 to 38 (CTCSS tone), depending on the

channel in use.

3) Press p or q to select the CTCSS tone in RX.

4) Press PTTtostorethetone(orwaitveseconds).

5) Press MENU three times. The led blinks red.

6) Press p or q to select the desired CTCSS tone in TX. Push PTT

to store the tone (or wait 5 seconds)

5.9.b Selecting the DCS codes

1) Select the operating channel.

2) Press MENU three times. DCS displays on the left along with the

ashingvaluethathasbeensetontheright:oF (disabled) or a

number ranging from 1 to 83, depending on the DCS code used.

3) Press p or q to select the DCS setting in RX.

4) Press PTTorwaitvesecondstostoretheDCS code.

5) Push MENU three times. The led blinks red.

6) Push p/qto select the DCS code in TX.Push PTT to store the

DCS code in TX.

5.9.c LED operation with CTCSS/DCS

Whenyouusetherestrictedtrafcmode,thestatusLEDprovides

slightlydifferentindicationsascomparedtothoseoftheopentrafc

mode:

• Off: indicates that no signal is being received (as in the open

trafcmode)

• Green: indicates that a signal with a correct CTCSS/DCS tone is

being received (it is enabled together with the radio volume)

• Orange: indicates the receipt of a signal without a CTCSS/DCS

tone or with a different CTCSS/DCS tone (the volume will not be

enabled)

• Red: indicates that the transmission is in progress (as in the open

trafcmode)

5.10 Monitoring function - Monitor/squelch

This feature can be used to monitor the selected channel before

transmitting and receiving low intensity signals. Press MON to

disable the mode (CTCSS).

To disable the squelch (noise reduction), hold MON down for

approximately 3 seconds. In this mode, you can hear all the noise

present in the environment.

2The disabling of the squelch increases the consumption of the

battery power.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland Alan HP450 2A Rugged Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland Alan HP450 2A Rugged

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info