Bedienungsanleitung Midland BT NEXT CONFERENCE (Seite 23 von 118) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579651

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

22 - Midland BT Next

How to pair two BT Next Conference units

The two units supplied in the same BT Next C. box, are already paired and ready to

use, which mean you don’t need to perform this procedure. The units are already

paired using the Middle button.

If the devices are not part of the same kit, or the units has been purchased separa-

tely, you need to rst pair it in order to use it.

To pair the BT Next C. to another BT Next Conference unit

To pair the BT Next C. to another BT Next C. unit, you must rst enter the setup mode:

1. Turn o the unit

2. Press and hold down the middle button about 7 sec., until the Red light is on

permanently.

3. Now press the Middle button for 3 seconds. The Blue and Red light will ash.

4. Do the same procedure on the other unit. When successfully paired, each unit

will have the Blue light on for one second and than go back to the setup mode

(Red light always on).

5. Now the pairing procedure is complete, you just need to exit the setup mode

before you can use the units.

6. Double click on the Middle button, the Red light will turn o and the Blue light

will start ashing.

You can use now your BT Next C..

Attention: remember to switch o all the other Bluetooth device, only the two devices

involved in the pairing must be turned on.

How to use the Intercom with two units

To use the intercom feature, be sure the both units are turned on and correctly paired

together.

Attention: For intercom communication between Driver and Passenger, there is no

need to keep the ip up antenna in the up position. For Bike-to-Bike intercom the an-

tenna must be in the upper position.

Manual activation

Press the Middle button on one of the two units. Communication is enabled and

remains active until you press again the middle button. The intercom need some

seconds to activate, you will hear a beep tone when the intercom is open.

Voice activation (VOX)

Simply start talking, after some seconds the communication will be opened and will

remain active for the time you are talking. If there is no conversation the intercom

will be closed after 40 seconds. If needed you can close the intercom manually wi-

thout waiting 40 seconds (just press the middle button).

If needed, you can disable the VOX feature simply by pressing the Backward button

for 7 sec. A voice announcement will advise you when the VOX is disabled. To turn the

VOX on again, just press the same button and a voice announcement will advise you

that the VOX is now active. This setting is remembered also in you turn o the unit.

Attention: The Voice activation (VOX) can open the intercom communication only to

the unit that was paired with the Middle button. If you choose to use a dierent button

(Rear or ), you will be able to active the intercom only manually.

Adjusting the volume

Your Midland BT Next C. uses AGC technology, which automatically adjusts the liste-

ning volume in relation to background noises.

However, it is also possible to manually adjust the volume by means of the “Volume

+” and “Volume -“buttons.

Attention: volume can be adjust only when an audio connection is active.

How to pair the BT Next Conference to more than two

units

One BT Next C. unit can be paired to maximum ve other BT unit, that mean six in

total (3 Midland unit + 2 Talk2All).

The BT Next C. has three main buttons (Forward, Middle and Rear). It is up to you

which button use to pair and activate the intercom, you are totally free to choose the

button you like more. The same button you will use to pair the unit will be also used

to activate the intercom communication.

Remember that each device can always be paired with other 3 units at your choice;

as shown in the picture here below, also ‘crossed’ pairing can be done.

For example you can decide to pair one motorbike rider unit to the Forward button,

your passenger to the Middle button and another rider to the Rear button.

In this way you can have in total 5 units paired together and talk to each person,

one by one, simply by pressing the corresponding button (the same used for the

Rider1

Rider2 Rider3

Passenger1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BT NEXT CONFERENCE Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info