Bedienungsanleitung Midland BT NEXT PRO (Seite 35 von 116) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

738682

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

www.midlandeurope.com 33

Enabling/disabling the wired input

If needed the wired input can be enabled or disabled:

Enabling/Disabling: Make a Long press (3 sec.) on the “Forward” and “Middle” buttons

(you will hear one audio beep tone for enabling conﬁrmation and two audio beep tones

for disabling). This setting is rembered also after turning On/O the unit.

Wired audio in background

The audio from the wired connection can be in background to your Intercom or Phone

communication. By default this option is ON. Please refer to the paragraph “Wired

connection always in background” below to disable it.

Note that is not possible to have the wired audio source in background to the FM radio.

Emergency Stop light

On the back of your BTX1 PRO mounting kit you have an ultra bright

LED emergency stop light. Every time you make a full brake, the stop

light will turn ON to give an extra alert to the drivers behind you. In case

you need to turn it OFF temporarily (for example when you ride with a

passenger), just press long “Backward” and “Forward” button together

while in “Phone” or “Intercom” mode (a voice announcement will con

ﬁrm the status). The unit will remember the last setting used, that mean

you need to turn ON manually the stop light pressing again “Backward”

and “Forward” button togheter.

Attention: By default the stop light is OFF

Setup and special conﬁgurations

Resetting all paired devices

Sometimes you may ﬁnd it necessary to delete all the pairing references stored in the

Midland BTNEXT PRO unit (reset operation).

To perform this operation you must ﬁrst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is on per

manently.

› Then simultaneously press and hold down the “Volume +” and “Volume –“ buttons

for 3 seconds. The Blue Light will be lit on for 1 sec and then back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the Midland

BTNEXT PRO.

This procedure deletes all the paired Bluetooth devices stored in the memory and it is

therefore possible to start a new “clean” pairing session.

Attention: after resetting all the pairting, only the “FM Radio” mode wil be available.

Back to factory setting

Sometimes you may ﬁnd it necessary to go back to the factory setting, to reset all the

changes/setup already made and have a “clean” unit.

To perform this operation you must ﬁrst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is on per

manently.

› Then simultaneously press and hold down all the three buttons “Forward”-“Midd

le”-“Backward” for 3 seconds. The Blue Light will be lit on for 1 sec and than back to

steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the Midland

BTNEXT PRO

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX acti-

vation is inﬂuenced by the helmet type, the background noise and therefore by the

speed.

For optimum results, it is possible to choose one of the following four microphone sen

sitivity levels: high, medium, low and very low. It is also possible to disable the VOX

feature in order to activate the Intercom and phone call answering features in manual

mode only.

Adjusting the sensitivity of the (VOX)

To perform this operation you must ﬁrst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is on per

manently.

3. Your Midland BTNEXT PRO is now in “Set up mode”.

Stop Light

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BT NEXT PRO Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info